Jacuzzi sasha Manual De Instalación página 20

- on the glass profile,
- on the roof frame.
The spacers should be positioned against the wall profiles (part. 2).
NOTE: (detail 1) the thickness of spacers varies: any glass perpen-
dicularity errors can therefore be corrected, for example, by placing
one spacer higher than the other.
Models with screen-printed glazing:
n
This glass, which features near transparent areas, must
be installed according to a specified order. Therefore,
refer to the drawings attached in order to identify the
correct assemble sequence.
NOTE: the screen-printed glass side must face inwards.
✐
15-15a, details 1-2) After having measured the length,
■ (
cut sections from the sealant roll which must be applied to the:
- bottom glazing bead (f-i)
- vertical glazing bead (f-i)
- top glazing bead (f-i)
NOTE: it is recommended to cut approx. 5 cm more of the sealant
than the nominal length and then remove any remaining length
once assembly is complete.
✐
15-15a, details 3-4) Position the small glass panel on
■ (
the plastic spacers and allow it to run so that it rests against the
spacers on the vertical profile.
✐
15-15a, detail 5) Check the spirit level of the roof panel (to
■ (
correct any perpendicularity errors, use spacers with a different thick-
ness).
✐
15-15a, detail 6) Install the glazing beads
■ (
✐
■ ( 16-16a, details 1-2) After having measured the length, cut
some sections from the sealant roll which must be applied to the:
- bottom glazing bead (f-i)
- vertical glazing bead (f-v)
- top glazing bead (f-s)
NOTE: it is recommended to cut approx. 5 cm more of the sealant
than the nominal length and then remove any remaining length
once assembly is complete.
✐
■ ( 16-16a, details 3-4) Position the large glass panel on
the plastic spacers and allow it to run so that it rests against the
spacers on the vertical profile.
✐
■ ( 16-16a, detail 5) Check the spirit level of the roof panel (to
correct any perpendicularity errors, use spacers with a different thick-
ness).
✐
■ ( 16-16a, detail 6) Install the glazing bead (even on doors,
present on base and ceiling frames, if removed during their instal-
lation).
Installing the heater (models with Sauna)
✐
17, details 1-2) Thread the sauna (S) and bio sauna (B)
■ (
power supply cables through the wall holes, positioning them in
the conduit behind the walls.
✐
17, detail 3) Draw the cables to the electrical box, thread-
■ (
ing them in the relevant cable clamps.
Connect the cables to the provided terminals, as indicated.
✐
17, detail 4) Attach the heater (contained within its packag-
■ (
ing) to the base wall, following the instructions already provided.
✐
■ ( 18, details 1-2) Where installation of the automatic filling
tank is planned, assemble the float and fix the tank on the heater
side, as indicated.
✐
18, details 3-4) Connect the supply pipe (3/4", coming
■ (
from the wall connection) to the tank, using a tap (not supplied);
then connect the tank to the heater, using the fitting (T) and the
tap (R) (supplied).
✐
■ ( 18, detail 5) Attach the heater to the bracket, as indicated.
✐
18, detail 6) Use running water to wash the stones, then
■ (
dry them and place them on the heater, ensuring to leave space
between one stone and another.
m Do not place the stones in layers! Always try and leave
space between stones, so that hot air coming from be-
low can circulate freely.
Installing the lower covers
✐
19, details 1-2) Remove the protective film from the cov-
■ (
ers and position them as indicated, checking their alignment
(firstly, you must insert the "I" covers under the small glass panel
couplers).
NOTE: the correct position is obtained by inserting the frame (see
also the "Accessories" chapter) between the cover and the alumin-
ium profile.
✐
19, detail 3-4) Once the correct position has been found,
■ (
place a line of silicone under each cover and assemble them as
indicated, according to the model.
✐
■ ( 19, detail 5-6) Also place the silicone in the areas between:
- the small glass panels and the external covers
- the large glass panels and the front covers
NOTE:
- (detail 5) to ensure greater stability, we recommended attaching
the support below the hinge above the cover (in the case of the
HAMMAM, we recommend placing silicone in the holes of the
cover to which the hinge is attached).
- remove any excess silicone below covers otherwise the assembly of
the wood cornice may prove difficult.
✐
■ ( 20, details 1-2) Place a line of silicone on the inner edge of
the covers and insert them between the glass panels and the base
20