Installation Instructions; Warranty Terms - Bossini Diamond Column L01702 Instrucciones De Montaje Y De Mantenimiento

DiamonD column

InstallatIOn InstrUCtIOns

Premise
To obtain an ideal shower column installation, the shower head (5) should be positioned at a height of
2000 mm from the floor (i.e. distance between the lower side of the shower head and the shower tray).
GB
Therefore, before installing the shower column, you are advised to check the dimensions and the
connections in your bathroom, considering that the Diamond Column do not allow any adjustment
to the pipe (1).
1) Check the maximum height of your bathroom, taking into account that the ideal overall product
dimensions reach a height of 2250 mm from the floor. See (Dwg. A).
2) It is important to check the connection system of your tap fittings. To install the Diamond column,
the shower tap (mixer, thermostatic or traditional) must be at a height of not less than 1100 mm
from the floor for the shower cubicle and not less than 750 mm for the bathtub.
3) Insert the central slider bracket (2) into the pipe (1), than fit the wall bracket (3) into the pipe (1)
paying attention to fit it in the proper site. See (Dwg. 1).
nB: The wall bracket (3) is provided with a standard spacer which allows the distance to be adjusted
between 52 and 68 mm from the wall (Dwg. B1). In the case of shower taps with a distance greater than
68 mm from the wall, use the special spacer included in the packaging(Dwg. B2), which allows the
distance to be adjusted from 68 to 83 mm.
4) Fit the pipe (1) on the tap and manually tighten the nut (Dwg.2). If necessary fit the two way diverter
(15) on exposed mixer (16) before to fit the shower pipe.
5) Ensure the shower pipe is perpendicular and perfectly lined up with the shower tap, than use a
pencil to mark the hole of the bracket (3) on the wall (Dwg. 3).
6) Screw down the nut and remove the pipe from the tap. Pay attention to protect the tap for possible
falling down of dirty material, than proceed to drill holes with an 8 mm bit (Dwg.4).
7) Insert the two anchors of 8 mm diameter in the wall holes (8), (Dwg. 5).
8) Fix the arm (4) into the wall bracket (3), tighten the fixing screw (14) ( Dwg. 8). Fit the pipe (1) on the
tap and manually tighten the lower nut; fix the wall bracket (3) with the two screws 5x50
included in the packing, than place the flange (Dwg. 6)
9) Finally tighten the lower nut (Dwg. 7) using the key included.
10) Fit the shower head (5) and finally fit the flexible hose (6) and the handshower (7) (Dwg. 8).
rECOMMEnDatIOns FOr PrOPEr UsE
Proper use of this product will allow you to avoid damages to the bathroom environment.
* To prevent impurities or debris from getting inside the product and causing functional problems,
always flush out the system before connecting it to the supply pipes.
It is recommended to install the filter at the system's water intake.
* To keep the diffuser clean and prevent lime scales from clogging the diffuser, we advise that you
periodically rub the silicone nozzles to free them of the lime deposits.
12
ClEanIng
Dear Customer,
Congratulations for choosing a Bossini product and we thank you for the trust you have given us. To
keep the material's appearance as long as possible, a few guidelines must be followed.
Cleaning metal parts: water contains calcium that deposits on surfaces and forms unpleasant spots.
For routine cleaning, simply use a damp cloth with a little soap, rinse and dry. Calcium spots can
therefore be avoided by drying after use.
Important note: Using only a soap-based detergent is recommended. Never use abrasive detergents
or disinfectants or those containing alcohol, hydrochloric acid or phosphoric acid, Bleach, chlorine etc
Cleaning the rubber nozzles: the showerhead is equipped with the "Easy-Clean" system with silicon
nozzles. Calcium is a shower's worst enemy and that is why Bossini proposes theEasy-Clean" system.
These silicon nozzles are extremely heat resistant and with hot water they dilate, thus detaching the
first layer of calcium. Moreover, periodically rubbing the silicon nozzles manually easily gets rid of
calcium. With one simple gesture, your shower is always perfect.
Dear Customer, we would like to remind you that the warranty on our product's surface is not valid if the
material undergoes treatment different than that suggested. The warranty does not cover any damage
due to deposits of calcium or impurities.

Warranty tErMs

Dear Customer,
We congratulate you and thank you for choosing a Bossini quality product
The product is covered by 2 Years warranty against any defects due to manufacturing faults.
the warranty does not cover damages caused by improper installation or use, neglect, incorrect
plumbing, normal fair wear and tear, damages caused by limescale deposits or impurities, the use of
detergents and maintenance products other than those specifically recommended in our instructions
manual. Furthermore Bossini is not responsible for labour costs and/or damages, whether accidental or
consequent to the installation, repairing or replacement of the product.
The request for replacement under the terms of this warranty must be made in a letter setting out the
date and place of purchase and giving a brief explanation of the problem. The letter must be received
by us within the warranty period and must be accompanied by proof of the purchase date (e.g. a
receipt). The warranty only covers production faults / defects and is strictly limited to the repair or free
replacement of the parts which are recognised to be defective. The defective parts have to be returned
to Bossini carriage free with a report describing the defect. Bossini reserves the right to inspect the part
alleged to be faulty or defective and to evaluate the applicability of the warranty terms.
the warranty period commences on the date the product is purchased, evidenced by the relevant
purchase document (e.g. receipt, invoice, cash voucher) and it is NOT renewable.
For further information please contact Bossini or its distributor.
DiamonD column
GB
13