DeWalt DCW210 Traducido De Las Instrucciones Originales página 34

EnGLIsH
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Use only D
e
Inserting and Removing the Battery Pack
from the Tool (Fig. C)
nOTE: Make sure your battery pack
To Install the Battery Pack into the Tool Handle
1. Align the battery pack 7 with the rails inside the sander's
battery port (Fig. C).
2. Slide it into the battery port until the battery pack is firmly
seated and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the release button 8
out of the battery port.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs
Some D WALT battery packs include a fuel gauge which
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge button.
A combination of the three green LED lights will illuminate
designating the level of charge left. When the level of charge
in the battery is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Attaching Sanding Discs (Fig. D)
Your sander is designed to use 125 mm sanding discs
an 8-hole dust extraction pattern. Sanding discs for the DCW210
attach with hook and loop.
To Attach Sanding Disc to the Sanding Pad
(Fig. D)
1. Turn the sander over so that the sanding pad
facing upward.
2. Clean the dust from the sanding pad
3. Hold the pad with one hand to keep it from rotating.
4. With the other hand, align the holes and place the sanding
disc directly on top of the pad.
10
nOTE: These sanders are not to be used in drywall applications.
Using a sanding screen (e.g., screen used for sanding drywall)
32
WALT battery packs and chargers.
7 is fully charged.
and firmly pull the battery pack
with
10
6 is
6 face.
directly on the hook and loop pad will not hold and will damage
the hooks on the pad. The hooks on the pad will wear very
rapidly if left in contact with the work surface while the tool
is operating.
Switch (Fig. A)
To turn the unit on, depress the side of the dust-protected
switch 1 that corresponds to the symbol "I". To turn the tool
off, depress the side of the switch that corresponds to the
symbol "O".
Speed Control Dial (Fig. A)
The speed control dial 2 , shown in Figure A, allows you
to increase or decrease speed from 8000–12000 Orbits Per
Minute. The optimal speed setting for each application is very
much dependent on personal preference. Generally, you will
want to use a higher setting on harder materials and a lower
setting on softer materials. Material removal rate increases as
speed increases.
Dust Extraction (Fig. A, E, G)

WARNING: Since woodworking with a sander produces
dust, always install a dust bag designed in compliance
with the applicable directives regarding dust emission.

WARNING: Do not use a dust bag or vacuum extractor
without proper spark protection when sanding metal.
Your sander has two dust extraction methods: a built-in port
which allows either the supplied dust bag
system to be connected; and a dust skirt (
built-in port utilizes the D WALT airlock connection making
e
it compatible with the D WALT dust extractor and airlock
e
accessory DWV9000.
To Attach the Dust Bag
1. While holding the sander, fit the dust bag collar
dust port as shown in Figure E.
3
2. Turn the collar 5 clockwise to lock the dust bag
To Empty the Dust Bag
nOTE: Be sure to wear approved eye protection and approved
dust mask when performing this procedure.
For efficient dust extraction, empty the dust collector when it is
about one third full.
1. While holding the sander, turn the collar
unlock the dust bag .
4
2. Remove dust bag from the sander and gently shake or tap
the dust bag to empty.
3. Reattach the dust bag back onto the dust port and lock into
place by turning the dust bag collar clockwise.
You may notice that all the dust will not come free from the
bag. This will not affect sanding performance but will reduce
the sander's dust collection efficiency. To restore your sander's
dust collection efficiency, depress the spring inside the dust bag
when you are emptying it and tap it on the side of the waste bin
or dust receptacle.
3
4 or a shop vacuum
, Fig. G). The
11
5 to the
4 in place.
5 anticlockwise to