Description And Specifications Description; Specifications - RIDGID ProPress Manual Del Operador

ProPress
Description and Specifications
Description
RIDGID Press Tool Attachments for ProPress
when used with the appropriate RIDGID Press Tool, are
designed to mechanically press ProPress fittings onto
tubing to create a watertight and permanent seal. When the
switch on the press tool is depressed, a motor powers a
hydraulic pump which forces fluid into the press tool cylin-
der. This moves the tool rollers forward into contact with the
attachment and applies thousands of pounds of force to the
specially designed fitting.
NOTE! ProPress ® is a registered trademark of Viega
GmbH & Co.
The entire pressing cycles takes between 4 and 8 seconds
starting from when the switch is pressed. Once the press-
ing tool starts to deform the fitting, the tool will automati-
cally continue the press until complete.
There are RIDGID Press Tool attachments for the fol-
lowing ProPress Systems:
• ProPress
• ProPress XL-C
ProPress
RIDGID makes jaw sets, rings and actuators to press
ProPress fittings. These include:
• Standard Series ProPress Jaw sets for
ProPress fittings
• Compact Series ProPress Jaw sets for
ProPress fittings
• ProPress Rings for 1 /
2
– 1 1 / " and 2" ProPress Rings are used with Standard
2
Series Press Tools with the V2 actuator
– 1 / " to 1 1 / " ProPress Rings can be used with the
2 4
Standard Series Press Tools with the V1 Actuator,
or with the Compact Series Press Tools with the C1
actuator
Standard Series ProPress Jaw Sets
Standard Series ProPress Jaw Sets are designed to
mechanically press ProPress fittings onto
1 1 / " and 2" tubing. An individual jaw set is required for each
2
size tubing. Standard Series Jaw sets are designed to
be used with RIDGID Standard Series Press Tools such as
the CT-400, 320-E, RP 330 and RP 340. Standard Series
Jaw Sets cannot be used with RIDGID Compact Series
press tools such as the 100-B, RP 200 and RP 210. Jaw
sets and press tools must be used perpendicular to the fit-
ting/tube being pressed.
2
® Fitting System
® Systems,
1 / " to 2"
2
1 / " to 1
2
" to 2" ProPress fittings:
1 / ", 3 / ", 1", 1
2 4
Catalog No.
76652
76657
76662
76667
76672
76677
Figure 1 – Standard Series ProPress Jaw Set
Compact Series ProPress Jaw Sets
Compact ProPress Jaw Sets are designed to mechanically
press ProPress fittings onto
individual jaw set is required for each size tubing. Compact
Series Jaw sets are designed to be used with RIDGID
Compact Series Press Tools such as the 100-B, RP 200
and RP 210. Com pact Series Jaw Sets cannot be used
with RIDGID Standard Series press tools such as the
CT-400, 320-E, RP 330 and RP 340. Jaw sets and press
tools must be used perpendicular to the fitting/tube being
1 / "
pressed.
4
Catalog No.
16958
16963
16978
31228
1 / ",
4
Figure 2 – Compact Series ProPress Jaw Set
ProPress Rings
ProPress Rings are designed to mechanically press
ProPress fittings onto
individual ring is required for each tubing size.
Size Weight
"
1 / 3.75 lbs. (1,70 kg)
2
"
3 / 3.90 lbs. (1,76 kg)
4
"
1 4.15 lbs. (1,88 kg)
"
1 1 / 4.30 lbs. (1,95 kg)
4
"
1 1 / 6.45 lbs. (2,93 kg)
2
"
2 9.40 lbs. (4,26 kg)
1 / ", 3 ⁄ ", 1" and 1 1 / " tubing. An
2 4 4
Size Weight
1 / " 2.5 lbs. (1,14 kg)
2
3 / " 2.22 lbs. (1,01 kg)
4
1" 2.28 lbs. (1,03 kg)
1 1 / " 2.56 lbs. (1,15 kg)
4
1 / ", 3 / " 1", 1 1 / ", 1 1 / " and 2" tubing. An
2 4 4 2
1 /
2
" through