Setting The Detector; Dip Switch Sw1; Dip Switches - Interlogix DD1012 Manual De Instrucciones

Figure 11
(1) Alarm relay
(2) Alarm zone
(3) Tamper switch output

Setting the detector

See Figure 14 for jumpers and DIP switch location.
Jumpers
Jumpers set onboard EOL mode and value. The circuit is
shown in Figure 11.
JA: Set onboard alarm EOL resistor (Ra)
1 kΩ
4.7 kΩ (factory
default)
Off: No onboard alarm EOL.
JT: Set onboard tamper EOL resistor (Rt)
1 kΩ
4.7 kΩ (factory
default)
Off: No onboard tamper EOL.
Configuring the zone
To set up the zone, apply the following guidelines.
•
Select appropriate EOL resistor values with JA and JT.
For example, setting of jumper JT determines Rt value.
•
For isolated outputs remove JT.
•
Remove jumpers JA and JT to exclude onboard EOL
values.
For a single zone with all onboard resistors set, the zone
resistance can be the following.
Table 2: Zone resistance values
Zone state Value
0 Ω
Tamper (short)
Normal Rt
Alarm Rt+Ra
∞
Tamper (open)

DIP switches

Table 3: SW1, general settings
Switch Values
6: LED On: LED on*
5: Remote On: Remote on
4: Reserved
3: Polarity On: Positive polarity
P/N 146550999-1 (ML) • REV M • ISS 19AUG19
Ra Alarm EOL resistor
Rt Tamper EOL resistor
2.2 kΩ
5.6 kΩ
2.2 kΩ
5.6 kΩ
Default
0 Ω
4.7 kΩ
9.4 kΩ
∞
Off: LED off
Off: Remote off*
Off: Negative polarity*
Switch Values
1, 2: Radar 1 On, 2 On: 12 m (39 ft.)*
range
1 Off, 2 On: 9 m (30 ft.)
* Factory default

DIP switch SW1

SW1-1, SW1-2: Radar range
Use SW1-1 and SW1-2 to set the radar range exactly to fit the
application. The radar is of a range-gating type which means
that the range of detection is very accurate.
4 m (13 ft.)
6 m (20 ft.)
SW1-3: Polarity
On: Positive polarity. Configures the inputs (WT and D/N) as
"Active high".
Off: Negative polarity. Configures the inputs (WT and D/N) as
"Active low". Factory default.
The functionality is explained in Figure 10.
Figure 10
(1) Polarity high
(2) Polarity low
This function also depends on the SW1-5 setting. See "SW1-5:
Remote functionality" below.
SW1-4: Reserved
Do not change.
SW1-5: Remote functionality
On: Remote on. Enables WT and day/night inputs.
Off: Remote off. Disables WT and day/night inputs (factory
default).
The following functionality depends on the Remote setting.
Table 4: Functions dependent on the Remote setting
Item Description SW1-5 Remote on SW1-5 Remote off
SW1-3 Polarity Selectable
WT WT input Enabled
D/N D/N input Enabled
Other Green Mode Enabled in day
mode with no WT
Alarm memory Enabled in day
mode with no WT
See also "Connections" on page 4.
SW1-6: LEDs
On: LEDs are enabled. See "LEDs and outputs" on page 6 for
LED functionality.
Off: LEDs are disabled for any state.
1 On, 2 Off: 6 m (20 ft.)
1 Off, 2 Off: 4 m (13 ft.)
9 m (30 ft.)
12 m (40 ft.)
Factory default.
(3) Walk test
(4) Day/night
Positive only
Disabled
Disabled
Disabled
Disabled
5 / 40