General Characteristics; Technical Specifications; Preliminary Setting-Up - Genius BRAIN 03 Instrucciones Para El Uso

24 Vdc ELECTRONIC CONTROL UNIT FOR SWING GATES
USE INSTRUCTIONS - INSTALLATION INSTRUCTIONS
This 24 Vdc control unit for swing gates offers high performance and a wide range of adjustments: opening and closing
decelerations, possibility of managing one or two motors, management of opening and closing limit-switches, and the
possibility of managing two TIMECODERS.
A sophisticated electronic control constantly monitors the power circuit and disables the control unit in the event of
malfunctions that could impair efficiency of the electronic clutch.
The parameter settings and the operating logics are set and shown on a handy display, which indicates gate status
during normal operation. Operating times are adjusted by self-learning during programming.
The water-tight enclosure is designed to house the control unit, the toroidal transformer and any buffer batteries (op-
tional) having the characteristics and dimensions indicated in the table below.
Supply voltage of transformer Supply voltage of transformer Supply voltage of transformer Supply voltage of transformer
Supply voltage of control unit Supply voltage of control unit Supply voltage of control unit Supply voltage of control unit
Absorbed power Absorbed power
Motor max load Motor max load
Accessories max load Accessories max load
Flashing lamp/Courtesy light max. load Flashing lamp/Courtesy light max. load Flashing lamp/Courtesy light max. load Flashing lamp/Courtesy light max. load
Operating ambient temperature Operating ambient temperature Operating ambient temperature Operating ambient temperature
Protection fuses Protection fuses
Function logics Function logics
Opening / closing time Opening / closing time Opening / closing time Opening / closing time
Pause time
Thrust force
Decelerations Decelerations
Terminal board inputs Terminal board inputs
Radio connector Radio connector
Terminal board outputs Terminal board outputs
Board dimensions Board dimensions
Characteristics of 230V~ toroidal transformer Characteristics of 230V~ toroidal transformer
Characteristics of 115V~ toroidal transformer Characteristics of 115V~ toroidal transformer
Characteristics of optional batteries Characteristics of optional batteries
Characteristics of outdoor enclosure Characteristics of outdoor enclosure
Different output values can be obtained on the 24V~ voltage depending on the mains voltage value. Before Different output values can be obtained on the 24V~ voltage depending on the mains voltage value. Before
start-up, always check the transformer output voltage. This must not exceed 26V~ for both 230V~ and 115V~ start-up, always check the transformer output voltage. This must not exceed 26V~ for both 230V~ and 115V~
power supply. Voltage must be measured load free, i.e. with the transformer powered and disconnected from power supply. Voltage must be measured load free, i.e. with the transformer powered and disconnected from
the board. the board.
To ensure people's safety, all warnings and instructions in this booklet must be carefully observed. Incorrect To ensure people's safety, all warnings and instructions in this booklet must be carefully observed. Incorrect
installation or incorrect use of the product could cause serious harm to people. installation or incorrect use of the product could cause serious harm to people.
Make sure there is an adequate differential switch upstream of the system as specified by current laws, and install an Make sure there is an adequate differential switch upstream of the system as specified by current laws, and install an
all-pole thermal breaker on the power supply mains.
To lay electric cables, use adequate rigid and/or flexible pipes.
Always separate the connection cables of low voltage accessories from the 115/230 V~ power cables. To prevent any
interference whatever, use separate sheaths.
Maximum length of power cables between control unit and motors must not exceed 10 m, using cables of
2.5mm² diameter.
To secure the various components inside of the airtight enclosure, refer to paragraph 15.

1. GENERAL CHARACTERISTICS

2. TECHNICAL SPECIFICATIONS

Automatic / Stepped Automatic / Semiautomatic / Step- Automatic / Stepped Automatic / Semiautomatic / Step-
Total opening / Pedestrian opening / Opening-closing Total opening / Pedestrian opening / Opening-closing
safety devices / Stop / Opening-closing limit-switch safety devices / Stop / Opening-closing limit-switch safety devices / Stop / Opening-closing limit-switch safety devices / Stop / Opening-closing limit-switch
24Vdc power supply to accessories / 24 Vdc Motors / 24 24Vdc power supply to accessories / 24 Vdc Motors / 24
Vdc Courtesy light-Flashing lamp / 12 Vdc/~ Electric lock Vdc Courtesy light-Flashing lamp / 12 Vdc/~ Electric lock Vdc Courtesy light-Flashing lamp / 12 Vdc/~ Electric lock Vdc Courtesy light-Flashing lamp / 12 Vdc/~ Electric lock

3. PRELIMINARY SETTING-UP

13
230/115 V~ (+6 -10%) - 50/60 Hz. 230/115 V~ (+6 -10%) - 50/60 Hz.
24 V~ (+6 -10%) - 50/60 Hz. 24 V~ (+6 -10%) - 50/60 Hz.
3 W
70 W x 2
24Vdc 500mA
24Vdc 15W max.
-20°C +50°C
4
ped Semiautomatic / Condo type ped Semiautomatic / Condo type
Through self-learning during programming Through self-learning during programming Through self-learning during programming Through self-learning during programming
Through self-learning during programming Through self-learning during programming Through self-learning during programming Through self-learning during programming
Four levels adjustable on display
Opening and closing
Power supply 24V~ / Battery supply / Encoder Power supply 24V~ / Battery supply / Encoder
Rapid 5-pin connector
165 x 130 mm.
prim. 230V~ / sec. 22V~ / 120VA
prim. 115V~ / sec. 20V~ / 120VA
12V - 4 Ah / dimens. 90 x 70 x 108 mm. 12V - 4 Ah / dimens. 90 x 70 x 108 mm.
306 x 225 x 130 mm. - IP55