Technical Parameters - GRAPHITE 58G952 Manual Del Usuario

página de 144

/ 144
Contenido
Tabla de contenido
Marcadores

Tabla de contenido

Idiomas disponibles

• Clean plastic parts with mild detergent and a sponge.

• You can proceed with maintenance actions only described

within this instruction manual. Any other action can be carried

out only by authorized service.

• Do not make any changes in chain saw construction.

• When not in use, chain saw should be stored clean, on flat

surface, in dry place and beyond reach of children.

When storing it is important to avoid deposition of rubber

particles in basic parts of the fuel system, such as carburettor,

fuel filter, fuel line and fuel tank. Fuels with alcohol additives

(ethanol or methanol) may absorb moisture, and that during

storing causes separation of fuel blend ingredients and

formation of acids. Acidic petrol may damage the engine.

AIR FILTER

Dirty air filter reduces efficiency of combustion engine and

causes increase of fuel consumption. Clean the air filter after

each 5 hours of the saw operation.

• Clean the air filter lid (4) and its surroundings, so the dirt does

not get into carburettor chamber after the lid is removed.

• Unscrew knob for air filter lid (3) and remove air filter lid (4).

• Remove air filter (d) (fig. T).

• Use water with soap to clean the filter, wash with clean water

and dry thoroughly.

• Install air filter. Ensure the grooves on the air filter rim match

protrusions on the air filter lid (4).

• When installing the air filter lid (4) make sure to properly

place ignition plug wire and access sleeves for carburettor

adjustment screws.

Do not wash the air filter in petrol or any other flammable

solvent to avoid fire hazard or appearance of dangerous

vapours.

CYLINDER FINNING

Dust deposition on the cylinder finning may cause motor

overheating. Check regularly and clean the cylinder finning

when carrying out maintenance of the air filter.

GUIDE BAR AND CHAIN

Check condition of the guide bar and chain every 5 hours of the

saw operation.

• Set the ignition switch (14) to off position.

• Loosen and unscrew the guide bar fixing nuts (7).

• Remove the casing (10) and disassemble guide bar (20) and

chain (21).

• Clean oil holes and groove (e) in the guide bar (20) (fig. U).

• Lubricate tip chain wheel of the guide bar (22) through the

hole (f) located on the guide bar tip (fig. W).

• Check condition of the chain (21).

CHAIN SHARPENING

Pay attention to cutting tools. Cutting tools should be sharp and

clean, it allows efficient and safe operation. Operating the saw

with blunt chain causes quick wear of the chain, guide bar and

driving chain wheel, and breaking the chain in the worst case.

That is why it is important to sharpen the chain on time.

Chain sharpening is a complex operation. Sharpening the

chain by yourself requires use of special tools and skills. It is

recommended to entrust sharpening the chain to qualified

persons.

FUEL FILTER

• Unscrew the fuel filler plug (15).

• Use wire hook to remove the fuel filter (g) through the fuel

filler hole (fig. X).

• Disassemble the fuel filter and wash it in petrol or replace with

a new one.

• Install the fuel filter in the tank.

• Tighten the fuel filler plug (15).

When the filter has been dismantled use the wire hook to hold

up the end of the suction line.

Be careful during fuel filter installation to prevent

contamination from getting into the suction line.

OIL FILTER

• Unscrew oil filler plug (18).

• Use wire hook to remove the oil filter (h) through the oil filler

hole (fig. Y).

• Wash the oil filter in petrol or replace with a new one.

• Remove dirt from the tank.

• Install the oil filter in the tank.

• Tighten oil filler plug (18).

When putting the oil filter into the tank make sure it reaches

front right corner.

IGNITION PLUG

To maintain reliable operation of the device, check condition of

the ignition plug on a regular basis.

• Remove air filter lid (4).

• Remove air filter (d).

• Remove wire (i) from the ignition plug.

• Put on plug key (included) and unscrew the ignition plug (fig.

Z).

• Clean and adjust spacing between contacts (0.65 mm) (replace

ignition plug when necessary).

OTHER INSTRUCTIONS

Ensure there are no fuel leaks, loosened joints or damages of

main parts, especially main handle joints and guide bar fixing.

When you find any damage, make sure it is repaired before next

use of the chain saw.

All faults should be repaired by service workshop authorized by

the manufacturer.