Technical Data - Berner BCDH-5-1 Manual Original

All manuals and user guides at all-guides.com
OBJ_BUCH-744-002.book Page 12 Friday, September 12, 2008 11:12 AM

Technical Data

Demolition Hammer
Art. No.
Rated power input W
-1
Impact rate min
Impact energy per stroke J
Chisel positions
Tool holder
Lubrication
Weight according to
EPTA-Procedure 01/2003 kg
Protection class
The values given are valid for nominal voltages [U] of
230/240 V. For lower voltage and models for specific coun-
tries, these values can vary.
Declaration of Conformity
We declare under our sole responsibility that the
product described under "Technical Data" is in con-
formity with the following standards or standardization
documents: EN 60745 according to the provisions of
the directives 2004/108/EC, 98/37/EC (until
28 Dec 2009), 2006/42/EC (from 29 Dec 2009),
2000/14/EC.
2000/14/EC: Measured sound
97 dB(A). Conformity assessment procedure accord-
ing to Annex VI.
Notified body:
TÜV NORD CERT GmbH & Co. KG,
Am TÜV 1, 30519 Hannover
Technical file at:
Albert Berner Deutschland GmbH, Bernerstraße 6,
D-74653 Künzelsau
Künzelsau, 21.07.2008
Jörn Werner Ulrich Lindner
CEO COO
21.07.2008, Albert Berner Deutschland GmbH;
Bernerstraße 6; D-74653 Künzelsau
Noise/Vibration Information
Measured values determined
2000/14/EG and EN 60745.
Typically the A-weighted noise levels of the product
are: Sound pressure level 86 dB(A); Guaranteed
sound power level lower than 105 dB(A). Uncertainty
K=3 dB.
Wear hearing protection!
12 | English
Vibration total values (triax vector sum) determined
according to EN 60745:
Chiselling: Vibration emission value a
BCDH-5-1
Uncertainty K=1.5 m/s
050581
The vibration emission level given in this information
1150
sheet has been measured in accordance with a stand-
1300– 2900
ardised test given in EN 60745 and may be used to
2– 13 compare one tool with another. It may be used for a
preliminary assessment of exposure.
12
The declared vibration emission level represents the
SDS-max
main applications of the tool. However if the tool is
Central
used for different applications, with different accesso-
permanent
ries or poorly maintained, the vibration emission may
lubrication
differ. This may significantly increase the exposure
level over the total working period.
5.8
An estimation of the level of exposure to vibration
/II
should also take into account the times when the tool
is switched off or when it is running but not actually
doing the job. This may significantly reduce the expo-
sure level over the total working period.
Identify additional safety measures to protect the
operator from the effects of vibration such as: main-
tain the tool and the accessories, keep the hands
warm, organisation of work patterns.
Assembly
Before any work on the machine itself, pull
power level the mains plug.
Auxiliary Handle
Operate your machine only with the auxiliary
handle 9.
The auxiliary handle 9 can be set to any position for a
secure and low-fatigue working posture.
Turn the bottom part of the auxiliary handle 9 in coun-
terclockwise direction and swivel the auxiliary handle
9 to the desired position. Then retighten the bottom
part of the auxiliary handle 9 by turning in clockwise
direction.
Changing the Tool
With the SDS-max tool holder, simpler and easier tool
changing is possible without additional aids.
The dust protection cap 1 largely prevents the entry of
drilling dust into the tool holder during operation.
When inserting the tool, take care that the dust pro-
tection cap 1 is not damaged.
according to
A damaged dust protection cap should be
changed immediately. We recommend hav-
ing this carried out by an after-sales service.
2
=8 m/s ,
h
2
.
1 619 929 E60 • 12.9.08