Mains Connection; Specified Conditions Of Use; Ec Declaration Of Conformity - Milwaukee MS 304 DB Manual Original

Do not clamp the protective swing guard.
Refrain from removing any cut-o s or other parts of the workpiece
from the cutting area whilst the machine is running and the saw
head is not in the rest position.
Never reach into the danger area of the plane when it is running.
Any faults with the machine, including any related to the safeguard
or the saw blades, must be reported to the persons in charge of safety
as soon as the faults are discovered.
Do not use any anges other than those supplied or indicated in the
instruction manual to secure the saw blade.
Replace the table insert when worn
Do not use saw blades which are damaged or deformed
Do not use saw blades not corresponding to the key data given in
these instructions for use.
Do not use saw blades made of high-speed steel.
Only use saw blades which have been properly sharpened. It is essen-
tial to adhere to the maximum speed speci ed on the saw blade.
Transport and store the tools in a suitable receptacle.
It is necessary to select a saw blade which is suitable for the material
being cut.
Never use the mitre saw to cut materials other than those speci ed in
the instruction manual.
Long workpieces must be adequately supported.
Stock having a round or irregular cross section (such as rewood)
must not be cut, as it can not be securely held during cutting. When
sawing thin stock layed on edge, a suitable auxilary fence must be
used for rm support.

SPECIFIED CONDITIONS OF USE

The mitre saw can be used for sawing solid wood, bonded wood,
glued veneer, materials similar to wood, aluminium pro les, Non-
ferrous metals and plastics.
Do not use this product in any other way as stated for normal use.

EC DECLARATION OF CONFORMITY

We declare under our sole responsibility that this product is in confor-
mity with the following standards or standardized documents.
EN 61029-1:2009 + A11:2010
EN 61029-2-9:2009
EN 55014-1:2006 + A1:2009 + A2:2011
EN 55014-2:1997 + A1:2001 + A2:2008
EN 61000-3-2:2006 + A1:2009 + A2:2009
EN 61000-3-3:2008
in accordance with the regulations
2011/65/EU (RoHs), 2006/42/EC, 2004/108/EC
Winnenden, 2013-01-10
Authorized to compile the technical le
Deutsch

MAINS CONNECTION

Connect only to single-phase AC current and only to the system
voltage indicated on the rating plate. It is also possible to connect
to sockets without an earthing contact as the design conforms to
safety class II.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all times.
Use only Milwaukee accessories and Milwaukee spare parts. Should
components need to be replaced which have not been described,
please contact one of our Milwaukee service agents (see our list of
guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state
the Article No. as well as the machine type printed on the label and
order the drawing at your local service agents or directly at: Milwau-
kee Electric Tool, Max-Eyth-Straße 10, D-71364 Winnenden, Germany.
SYMBOLS
Rainer Kumpf
Director Product Development
Please read the instructions carefully before starting
the machine.
Always disconnect the plug from the socket before
carrying out any work on the machine.
Wear ear protectors!
Always wear goggles when using the machine.
Always keep hands away from the path of the saw
blade.
Never expose tool to rain.
CAUTION! WARNING! DANGER!
Do not dispose of electric tools together with
household waste material! In observance of European
Directive 2002/96/EC on waste electrical and electronic
equipment and its implementation in accordance with
national law, electric tools that have reached the end of
their life must be collected separately and returned to
an environmentally compatible recycling facility.
Class II construction, tool in which protection against
electric shock does not rely on basic insulation only, but
in which additional safety precautions, such as double
insulation or reinforced insulation, are provided.
English English
GB GB
23