General Notes On Safety; Use Of The Machine For Purposes For Which It Is Intended; Incorrect Use; Declaration Of Incorporation - SUHNER ABRASIVE WH 15 Documentación Técnica

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 28
1. N
1.1 g
enerAl notes on sAfety
This operation manual is applicable for the WH 15 hand
tool and the AH 15 external receiver.
The hand tool may only be handled by personnel
who are qualified.
It is imperative that you observe the safety instruc-
tions provided separately for the drive.
1.2 u
se of the mAchine for purposes for
which it is intended
The hand tool is designed for dry applications on metal
surfaces. For clamping of type FDV MK2 and type FG
MK2 mandrels, for polishing and satin finishing with tools
with a diameter of up to 200mm.
1.3 i
ncorrect use
All uses other than those described under section
1.2 are regarded as incorrect use and are there-
fore not admissible.
1.4 d
eclArAtion of incorporAtion
The manufacturer Otto Suhner AG of Industriestrasse 10,
CH-5242 Lupfig, hereby declares for the partly completed
machinery (see reverse side for type and serial no.) that
the following fundamental requirements of the Directive
2006/42/EC are applied and fulfilled in accordance with
Annex I: 1.1.2, 1.1.3, 1.1.5, 1.2.1, 1.2.2, 1.3.7, 1.3.8.1, 1.5.1,
1.5.4, and 1.6.1. Technical documentation was generated
for the partly completed machinery in accordance with
Annex VII of the Machinery Directive. Document Agent:
T. Fischer. Authorised sites are provided with this techni-
cal documentation in paper or electronic form on justi-
fied request. This partly completed machinery may be put
into operation only when the machine in which the partly
completed machinery is to be incorporated has been as-
certained to fulfil the conditions under the Machinery Di-
rective. CH-Lupfig, 09/2020. T. Fischer/Division manager
2. C
2.1 A
ssembly instructions
hand tools.
Use only hand tools, shafts, and grinding tools in perfect
condition.
Attach the hand tool to the shaft only when the drive is
switched off and has come to a stop.
Connect grinding tools only when the drive is switched off
and has come to a stop.
20
S
oTES oN
aFETy
ommISSIoNINg
It is imperative that you
read Sections 2 and 3 be-
fore you start operating the
It is imperative that you use the guards intended for the

hand tool.

Observe the specifications applying to your country.
2.2 h
And tool
2.2.1 c
/d
onnecting
etAching the tool
Loosen the nut on the mandrel and remove the pressure
disc (1). Fit the tool (2). Fit the pressure disc and fasten
it using the nut (1). Disassembly must be carried out in
reverse order.
Only utilize tools and accessories which have
been approved by SUHNER.
The safety instructions issued by the tool manu-
facturer must also be observed.
Check that the diameter of the tool is within the permit-
ted limit and that the maximum permitted speed is higher
than the idle speed or set speed of the machine.
The assembled tool must be able to turn freely.
2.2.2 c
/d
onnecting
etAching the mAndrel
Insert the shaft of the mandrel into the receiving hole on
the handpiece (1). Lock the mandrel with the spanner (2).
Tighten the nut with a hook spanner (3) Disassembly must
be carried out in reverse order.

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Ah 15

Tabla de contenido