Tabla de contenido
Publicidad
14
15
19
20
English
Introduction
Congratulations on your purchase and welcome to Philips Avent! To fully
benefit from the support that Philips Avent offers, register your breast pump
at www.philips.com/welcome.
General description (Fig. 1)
1 Handle
2 Silicone diaphragm
3 Stem
4 Pump body
5 Cushion
6 White valve
7 Philips Avent Natural bottle*
8 Breast milk storage bags*
* For these accessories, a separate user manual is provided. Read the separate
user manuals carefully, as these contain important safety information.
Intended use
The Philips Avent manual breast pump is intended to express and to collect
milk from the breast of a lactating woman. The device is intended for a
single user.
Important safety information
Read this user manual carefully before you use the breast pump and save it
for future reference.
Contraindication
- Never use the breast pump while you are pregnant, as pumping
can induce labor.
WARNING!
Warnings to avoid choking, strangulation and injury:
- Do not allow children or pets to play with the breast pump parts,
packaging materials or accessories.
-
Inspect the breast pump for signs of damage before each use. Do not
use the breast pump if it is damaged or if it does not work properly.
Warnings to avoid contamination and to ensure hygiene:
-
For hygienic reasons, the breast pump is only intended for repeated use
by a single user.
-
Clean and disinfect all parts before first use and after each use.
-
Do not use antibacterial or abrasive cleaning agents to clean the breast
pump parts as this may cause damage.
-
Wash your hands thoroughly with soap and water before you touch
breast pump parts and breasts to prevent contamination. Avoid touching
the inside of containers or lids.
Warnings to avoid breast and nipple problems including pain:
-
Always release the handle before you remove the pump body from your
breast in order to release the vacuum.
-
If the vacuum is uncomfortable or causes pain, stop pumping and
remove the breast pump from your breast.
-
Do not continue pumping for more than five minutes at a time if you do
not succeed in expressing any milk. Try to express at another time during
the day.
-
If the process becomes very uncomfortable or painful, stop using the
pump and consult your healthcare professional.
-
Only use accessories and parts recommended by Philips Avent.
-
No modification of the breast pump is allowed.
Warning: If you are infected with Human Immunodeficiency Virus (HIV) or
Hepatitis B or C, using the breast pump will not reduce or remove the risk of
transmitting the virus to your baby through breast milk.
Caution
Caution to prevent damage to and malfunctioning of the breast pump:
-
Keep the parts away from heated surfaces to avoid deformation of these
parts.
16
17
21
22
9 Cushion cover
10 Bottle cap
11 Screw ring
12 Teat
13 Sealing disc
14 Adapter for cup
15 Philips Avent storage cup*
16 Storage cup lid
Preparing for use
18
Disassemble, clean and disinfect all parts before you use the breast pump
for the first time and after every use.
Caution: Be careful when you remove and clean the white valve. Do not
insert objects into the white valve, as this may cause damage.
Cleaning and disinfecting
Step 1: Disassembling
Disassemble the breast pump and bottle completely. Also remove the white
valve from the breast pump.
Step 2: Cleaning
The parts can be cleaned manually or in the dishwasher.
Step 2A: Manual cleaning
1
Rinse all parts under a running tap with lukewarm water.
2
Soak all parts for 5 minutes in warm water with some mild dishwashing liquid.
3
Clean all parts with a cleaning brush.
4
Thoroughly rinse all parts under a running tap with cold clear water.
5
Leave all parts to air-dry on a clean tea towel or drying rack.
Step 2B: Cleaning in the dishwasher
Note: Food colorings may discolor parts.
1
Place all parts on the top rack of the dishwasher.
2
Put dishwashing liquid or a tablet in the machine and run a standard
program.
3
Leave all parts to air-dry on a clean tea towel or drying rack.
Step 3: Disinfecting
Caution: During disinfection with boiling water, prevent the bottle or
other parts from touching the side of the pot. This can cause irreversible
product deformation or damage that Philips cannot be held liable for.
1
Fill a household pot with enough water to cover all parts and place all
parts in the pot. Let the water boil for 5 minutes. Make sure the parts do
not touch the side of the pot.
2
Allow the water to cool down.
3
Gently remove the parts from the water. Place the parts on a clean
surface, tea towel or drying rack to air-dry.
Assembling the breast pump
Make sure you have cleaned and disinfected the parts of the breast pump
that come into contact with milk.
Warning: Be careful, when you have disinfected the breast pump
parts by boiling them, they can be very hot. To prevent burns, only start
assembling the breast pump when disinfected parts have cooled down.
Check the breast pump kit parts for wear or damage before use and replace
them if necessary.
Note: Correct placement of the cushion and the silicone diaphragm is
essential for the breast pump to form a proper vacuum.
1
Insert the white valve into the pump body from underneath. Push the
valve in as far as possible (Fig. 2).
2
Screw the pump body clockwise onto the bottle (Fig. 3) or storage cup
(Fig. 4) until it is securely fixed.
Note: If you use a storage cup, you have to screw the adapter for cup
onto the storage cup first (Fig. 4).
3
Insert the stem in the silicone diaphragm (Fig. 5).
4
Insert the silicone diaphragm into the pump body from above. Make sure
it fits securely around the rim by pressing down with your fingers to
ensure a perfect seal (Fig. 6).
5
Attach the handle onto the diaphragm with stem by hooking the hole in
the handle over the end of the stem. Push down the handle onto the
pump body until it clicks into place (Fig. 7).
6
Place the cushion into the pump body (Fig. 8) and make sure that the
rim covers the pump body. Push in the inner part of the cushion into the
funnel against the line indicated with an arrow (Fig. 9).
Note: Place the cushion cover (SCF430/10, SCF430/13, SCF430/15) over
the cushion to keep the breast pump clean while you prepare for expressing.
Using the breast pump
Warning: Always use the breast pump with the cushion.
Note: Contact your healthcare professional in case of questions or if you
experience side effects.
Operating the breast pump
1
Wash your hands thoroughly with soap and water and make sure that
your breast is clean.
2
Press the assembled pump body against your breast. Make sure that
your nipple is centered, so that the cushion creates an airtight seal.
3
Gently start to press down the handle until you feel the suction on your
breast (Fig. 10). Then allow the handle to return to its resting position.
Repeat this step rapidly 5 or 6 times to initiate the 'let-down' reflex.
Publicidad
Tabla de contenido
Solución de problemas
