Stylies MIRA Instrucciones De Uso página 12

Aroma Box (17)
To add fragrance into the Aroma Box (17), irstly, make sure the power cable is NOT pluged in the
power supply. Remove the Top Cover (2) by lifting it up with hands. Put no more than 2–3 drops of
fragrance in the Aroma Box. Now the humidiier can release a pleasing fragrance in the room air.
Operation
• The humidiier is ready to operate when the Tank (6) is illed and the Cable (1) is pluged in the
main network.
Pressing the botton
•
This will light up LCD display (3.1) and the fan speed is at its initial speed, "SPEED 1". If it shows
•
"NO WATER" on the LCD display (3.1), pls check if the Water Tank (6) is illed with water.
LCD display (3.1) will show ">>" for 3 seconds, as the initial setup of the humidity level is "Con-
•
tinuous".
After this 3 seconds, the LCD display (3.1) will show the actual room humidity level.
•
Use knob (3.5) to choose the requested relative air humidity (range from 40 up to 65% and
•
then ">>" (as continuous)).
After setting is taken, the LCD Display will switch to show the actual humidity level.
•
When the desired humidity level is reached, the LCD Display will blinking with the actual humid-
•
ity and the fan will stop running until the room humidity level drops below the settled humidity.
• During this period, for every 30 minutes, the fan will automatically run for 2 minutes at speed 1.
Pressing button
•
After the setting is taken, the LCD display will switch to show the actual humidity level.
•
Pressing the button
•
4 hours and 8 hours. When not pressing the button longer than 5 seconds, the LCD display will
blinking with the remaining time from the previous setting, or, blinking with " TIMER 1".
After the setting is taken, the LCD display will switch to show the actual humidity level.
•
Pressing the button
•
the fan speed is automatically adjusted according to the environment humidity:
– env. Humidity is more than 45%: the fan speed is "0"– not running;
– env. Humidity is between 40% to 45%: Fan speed is "1";
– env. Humidity is between 30% to 40%: Fan speed is "2"; and
– env. Humidity is below 30%: Fan speed is "3"– the maximum speed level.
• By pressing this button for more than 5 seconds, can reset the timer for the Filter Cassettes.
A timer for 1440 hours is programmed to count the using time of the ilter cassettes. When
•
the time is up, on the LCD display it will show "FILTER" with blinking light. This indicates the ilter
cassettes need to be changed. After you have replaced the old cassettes with the new ones,
you can reset the timer by pressing this button longer than 5 seconds, and the blinking "FILTER"
will disappear after reset.
Pressing the button
•
level is set at 45%, the LCD display is dimmed, and the fan speed is at "SPEED 1".
Ionic Silver Cube (ISC™) (13)
The ISC™ with its patented technology prevents the growth of bacteria and germs. It can be used for
a maximum of one season, and must be replaced at the start of the next heating season (i.e. when
the weather becomes cold).
Despite using the Ionic Silver Cube (ISC™), you should reill the water tank with fresh water on a
daily basis.
After use
• Switch Of the unit.
Pull out the mains plug/Cable
•
(3.2) to switch the unit on.
(3.3) can adjust the fan speed from "SPEED 1" to SPEED 3".
(3.4) for more than 5 seconds can set the Timer from 1 hour, 2 hours,
(3.6) can start the "AUTO MODE". Under this automatic control mode,
(3.7) can set the unit into "SLEEP MODE". At this mode, the humidity
9