Publicidad
Idiomas disponibles
Idiomas disponibles
O. FUSE - The fuse is in the AC supply of the ampli-
fier and will help to protect the amplifier and oper-
ator in the event of an electrical fault. If a fuse
blows, it should only be replaced with a fuse in
accordance with the listing at the fuse holder. If
the amplifier repeatedly blows fuses, take the
amp to an authorized Fender service center.
P. POWER SWITCH - This switch turns the amplifi-
er ON and OFF.
Q. STANDBY SWITCH - In the STANDBY position,
the amplifier is off except power is still supplied to
the tube filaments which eliminates the normal
amp warm-up time. Use standby position for two
minutes at each power-up and during short
b reaks instead of the POWER SWITCH to
increase tube life.
R. MAIN SPEAKER JACK - Plug-in connection for
speakers. This jack must always be used as the
primary connection to speakers.
TUBES
The "CUSTOM" VIBROLUX REVERB tube complement consists of two Fender Special Design 6L6WGC/5881's (part num-
ber 039214), five Fender Special Design 12AX7A's (part number 013341), and one Fender Special Design 12AT7 (part num-
ber 023531). Fender's Special Design Tubes provide optimum performance in this amplifier. For best results, replace with
Fender original equipment tubes only. Tube location is printed on the tube label, inside the cabinet.
TYPE:
PART NUMBERS:
POWER OUTPUT:
OUTPUT IMPEDANCE:
INPUTIMPEDANCE:
FEATURES:
SPEAKER COMPLEMENT:
DIMENSIONS:
Height:
Width:
Depth:
WEIGHT:
R
e
a
r
P
a
R
e
a
r
P
a
S. EXTERNAL SPEAKER JACK - Plug-in connection
T. FOOTSWITCH JACK - Plug-in connection for the
S
p
e
c
i
f
i
c
a
S
p
e
c
i
f
i
c
a
CSR 8
(120V, 60Hz) USA, 021-5100-000,
(230V, 50Hz) Eur, 021-5160-000,
(230V, 50Hz) Nordic,021-5180-000,
40W R.M.S. minimum into 4Ω
4Ω.
Input 1, both channels: 1 MΩ / Input 2, both channels: 136 kΩ
Tube power amp, vibrato and reverb, tilt-back legs
Two 10 in. Jenson P-10's
19-3/8"
25"
8-5/8"
46lbs
Product specifications are subject to change without notice.
5
n
e
l
n
e
l
for an external speaker. This jack is wired in par-
allel with the MAIN SPEAKER JACK, and must
only be used with a speaker plugged into the
MAIN SPEAKER JACK. Should the EXTERNAL
SPEAKER JACK be used without also using the
MAIN SPEAKER JACK, there will be no sound.
Note that the amplifier is optimized for a 4 ohm
speaker load, and the speakers in the cabinet are
wired for 4 ohms. Should a total load of more or
less than 4 ohms be used, the amplifier will not
put out its maximum power output before distor-
tion occurs.
footswitch.
The footswitch allows re m o t e
ON/OFF switching of the VIBRATO and REVERB
effects.
t
i
o
n
s
t
i
o
n
s
(100V, 50/60Hz) Jpn, 021-5170-000,
(230V, 50Hz) UK, 021-5140-000,
(240V, 50Hz) Aust, 021-5130-000
(49.2 cm)
(63.5 cm)
(21.9 cm)
(21kg).
Publicidad
