DAB E.SYBOX MINI 3 Instrucciones Para La Instalación Y El Mantenimiento página 40

GB
ENGLISH
INDEX
Key
Warnings
Responsibility
1. General
1.1 Description of the Integrated Inverter
1.2 Integrated expansion vessel
1.3 Technical characteristics
2. Installation
2.1 Vertical Configuration
2.1.1 Hydraulic connections
2.1.2 Loading operation - Installation above head and below head
2.2 Horizontal Configuration
2.2.1 Hydraulic connections
2.2.2 Orientation of the interface panel
2.2.3 Loading operation - Installation above head and below head
3. Commissioning
3.1 Electrical connections
3.2 Configuration of the integrated inverter
3.3 Priming
4. The keypad and the display
4.1 Direct access with a combination of keys
4.2 Access by name with a drop-down menu
4.3 Structure of the menu pages
4.4 Blocking parameter setting by Password
4.5 Enabling and disabling the motor
5. Meaning of the individual parameters
5.1 User Menu
5.1.1 Status
5.1.2 RS: Rotation speed display
5.1.3 VP: Pressure display
5.1.4 VF: Flow display
5.1.5 PO: Absorbed power display
5.1.6 C1: Phase current display
5.1.7 SV: Supply voltage
5.1.8 SR: Supply range
5.1.9 TE: Dissipator temperature display
5.1.10 PKm: Pressure measured at suction
5.1.11 Operating hours and number of starts
5.1.12 PI: Power histogram
5.1.13 Output flow meter
37
5.1.14 VE: Version display
5.1.15 FF: Fault log display
40 5.2 Monitor Menu
40 5.2.1 CT: Display contrast
41 5.2.2 BK: Display brightness
5.2.3 TK: Backlight switch-on time
41
5.2.4 LA: Language
42
5.2.5 TE: Dissipator temperature display
42
5.3 Setpoint Menu
43
5.3.1 SP: Setting the setpoint pressure
5.4 Manual Menu
44
44 5.4.1 Status
5.4.2 RI: Speed setting
45
45 5.4.3 VP: Pressure display
5.4.4 VF: Flow display
46
46 5.4.5 PO: Absorbed power display
46 5.4.6 C1: Phase current display
47 5.4.7 RS: Rotation speed display
5.4.8 SV: Tupply voltage
48
5.4.9 SR: Supply range
48
5.4.10 TE: Dissipator temperature display
49
5.5 Installer Menu
49
5.5.1 RP: Setting the pressure fall to restart
5.5.2 OD: Type of plant
50
51 5.5.3 MS: Measuring system
5.5.4 EK: Setting the low pressure function on suction
54
54 5.5.5 PK: Low pressure threshold on suction
5.5.6 T1: Low pressure delay (function detecting low pressure on suction)
55
5.6 Technical Assistance Menu
55
5.6.1 TB: Water lack blockage time
56
5.6.2 T2: Delay in switching off
56
5.6.3 GP: Proportional gain coefficient
56
5.6.4 GI: Integral gain coefficient
56
5.6.5 RM: Maximum speed
56
5.6.6 AY: Anti Cycling
56
5.6.7 AE: Enabling the anti-block function
56
5.6.8 AF: Enabling the anti-freeze function
56
5.7 Setting low pressure detection on suction
56
5.8 RF: Fault and warning reset
56
5.8.1 PW: Change password
56
6. Protection systems
56
56 6.1 Description of blockages
6.1.1 "BL" Anti Dry-Run (Protection against dry running)
56
57 6.1.2 "Anti-Cycling (Protection against continuous cycles without utility request)
57
57
57
57
57
57
57
57
57
57
58
58
58
58
58
58
58
58
58
59
59
59
59
59
59
60
60
60
60
60
60
60
60
60
60
61
61
61
61
61
61
62
62
62