GRAPHITE 58G003 Manual Del Usuario página 16

CAUTION! Temperature of 130°C can be also defined as 265°F.
• Observe all charging instructions. Do not charge the battery
in temperature outside of range defined in the rating data
table from the instruction manual. Incorrect charging or
charging in temperature outside of defined range may damage the
battery and increase the risk of fire.
BATTERY REPAIRS
• Do not repair damaged batteries. Battery can be repaired
only by the manufacturer or in an authorised workshop.
• When disposing of the worn out battery, take it to a service
point where you can utilize such dangerous wastes.
SAFETY REGULATIONS FOR THE CHARGER
• Do not expose the charger to humidity or water. Ingress of
water into the charger increases risk of electric shock. Use the
charger only in dry rooms.
• Disconnect the charger from power supply before starting any
maintenance or cleaning.
• Do not use the charger when placed on flammable
surface (e.g. paper, textiles) or in proximity of flammable
substance. Greater charger temperature when charging
increases risk of fire.
• Check condition of the charger, cable and plug before each
use. Do not use the charger if any damage is found. Do not
try to disassemble the charger. All repairs should be made at
an authorized service workshop. Improper charger assembly may
cause electric shock or fire.
• Children or persons who are physically, emotionally or
mentally disabled and other persons, whose experience or
knowledge is insufficient to use the charger while following all
safety rules should not use the charger without supervision of
person responsible for their safety. Otherwise there is a risk of
improper use and injuries in consequence.
• When the charger is not in use, it should be disconnected
from the mains network.
• Observe all charging instructions. Do not charge the
battery in temperature outside of range defined in the
rating data table from the instruction manual. Incorrect
charging or charging in temperature outside of defined range
may damage the battery and increase the risk of fire.
CHARGER REPAIRS
• Do not repair damaged charger. The charger can be repaired
only by the manufacturer or in an authorised workshop.
• When disposing of the worn out charger, take it to a service
point where you can utilize such wastes.
CAUTION! This device is designed to operate indoors.
The design is assumed to be safe, protection measures and
additional safety systems are used, nevertheless there is
always a small risk of injuries at work.
Li-Ion batteries may leak, set on fire or explode when
heated to high temperature or short-circuited. Do not store
the batteries in a car in hot and sunny days. Do not open
the battery. Li-Ion batteries contain electronic protection
devices that, if damaged, may cause fire or explosion of the
battery.
Explanation of used symbols
1 2
5 6
9 10
14
13
Read instruction manual, observe warnings and safety
1.
conditions therein.
Use protective goggles and hearing protectors.
2.
Work with protective mask on.
3.
Keep the tool away from children.
4.
Protect against rain.
5.
Use indoors, protect from water and moisture.
6.
Be careful, sharp edges!
7.
Use protective gloves
8.
Recycling.
9.
Protection class 2.
10.
Segregated waste collection.
11.
Do not throw cells into fire.
12.
Hazardous to water environment.
13.
Do not allow to heat above 50°C.
14.
CONSTRUCTION AND USE
Angle grinder is a hand held, battery powered tool. Drive consists
of a DC commutator motor with permanent magnets, whose
rotational speed is transferred with angle gear transmission. It
can be used for grinding and cutting. This type of power tool
is widely used for removal of burrs from metal surfaces, weld
surface treatment, cutting tubes and other metal objects etc.
With the right equipment the angle grinder can be used not only
for cutting or grinding, but also removal of rust, paint coats etc.
Range of use covers all areas of repairs and construction in
internal furnishing, adaptation of premises etc.
The device is designed for dry operation only and cannot be
used for polishing. Use the power tool in accordance with the
manufacturer's instructions only.
Inappropriate use.
• Do not process materials that contain asbestos. Asbestos is a
carcinogen.
• Do not process materials that produce flammable or explosive
dust. During operation power tool produces sparks that can ignite
produced fumes.
16
3 4
7 8
Max.
50°C
12
11