Publicidad
Safety
Signs, symbols and instructions placed on this product must never be covered or removed and must remain present and clearly
legible throughout the entire lifetime of the product. Immediately replace or repair illegible or damaged signs, symbols and
instructions. Contact your local dealer for instructions.
In case of an adverse event occurred in relation to the device, incidents should be reported to your local dealer and the national
competent authority in a timely manner. The local dealer will forward information to manufacturer.
For information about product safety notices and product recalls, local dealer information are available at the website etac.com
EN
Caregiver
•
Read the "User Guide" carefully before use and keep it
for future reference. Incorrect use of this product may
cause serious injury to the user
•
Always use the correct lifting techniques and aids for
this purpose
•
Never leave the user unattended in this product. Ensure
permanent supervision by a caregiver
•
Repair/replacements must only be made using new
original R82 spare parts and fittings and carried out in
accordance with the guidelines and service intervals
prescribed by the supplier
•
Settings and adjustments to the product or accessories
are only to be made by persons who have read the
user guide and who has been given the necessary
instructions by a product advisor.
•
If there is any doubt as to the continued safe use of
your R82 product or if any parts should fail, stop using
the product immediately and contact your local dealer
as soon as possible
•
When adjusting the seat angle, keep a hand on the
seat mounted on the frame to ensure slow angling
•
Ensure that moving parts does not squeeze or trap
body parts when adjusting them
•
Ensure that body parts are not trapped in openings for
mounting of supports/accessories.
•
Do not let children and youngsters play with the
handset
•
It is important to remove the transport plastic bag
before using the handset. Cables need to be placed in
such a way that users or carers cannot trip and injure
themselves.
•
Always use the product in a moderate pace. Do not run
with the product
•
Information about transportation can be found in the
document "Transportation in Motor Vehicles" supplied
with the product
•
Information about roadability can be found in the
document "Roadability" supplied with the product
•
Information regarding frame and seat combinations
including max. load in combination can be found at:
etac.com
•
This product contains small parts which could present a
choking hazard if removed from their intended placing.
Environment
•
Observe the surface temperature on the product,
before placing an user in it. This goes especially for
users with insensitive skin as they cannot feel the heat.
If the surface temperature is above 41°C then allow
the product to cool before use
•
Use this product on a level surface without any
obstacles. Be aware of reduced maneuverability on
slippery surfaces
•
When using on inclines, please refer to measurements
User
•
If the user is close to the max. load limit and/or has
a lot of involuntary movements, e.g. rocking, a larger
size with a higher max. load or a different R82 product
should be considered
•
Do not place more than one user in the product
•
When changing user, clean the product and disinfect
it if necessary. Carry out necessary adjustments after
cleaning.
Product
•
Removable parts without use of tool: Foot support and
seat. The removal will have adverse effect on the device
•
Carry out all positional adjustments on the product
and accessories and ensure that all knobs, screws
and buckles are securely fastened before use. Keep all
tools out of the reach of children
•
Activate the brakes before placing the user into the
product
•
Ensure the wheels are fully-functional and secure
before use
•
The correct tyre pressure is printed on the tyre casing
and listed in the section for tyre technical data.
•
In case of a tyre puncture do not use the product until
remedied
•
Ensure the stability of the product is maintained before
placing the user in it
•
When the footplate is close to the floor and the castors,
the castors may be unable to swivel
•
If the frame has to be used in the lowest position,
remove the footrest before adjustment.
•
Inspect the product and all of its accessories and
replace any worn out parts before use
•
Do not expose the gas spring to pressure or high
temperatures. DO NOT puncture
•
Do not expose the piston rod to scratches etc. It is
important to use a cloth or the like, if tools are used to
adjust the gas spring
•
When mounting a Panda Futura seat size 4 on any
High-low:xo frame, you must mount the anti-tip device
that comes as an accessory to the product
•
The power unit does not have a safety stop
•
Do only use the power unit within specified working
limits
•
Do not attempt to repair any part of the power unit.
•
The user must not occupy the product when it is lifted
from the ground
•
Ease of access to and maneuverability in, motor
vehicles can be significantly affected by size of
device and turning radius, and the smaller device
and/or device with a shorter turning radius will
generally provide greater ease of vehicle access
and maneuverability to a forward facing position. In
accordance with ISO 7176-19 Annex D, the product
is evaluated regarding the ability to accommodate
vehicle-anchored pelvic and shoulder belts. The device
receives an overall score of "Good"
•
The device conforms to ISO 7176-8, covering
requirements and test methods for static, impact and
fatigue strengths
•
Unoccupied device is suitable for land and air transport
•
Details covering EMC can be found in the appendix
"EMC details" supplied with the product
•
Depending on the size, the device is intended for
occupant mass groups I and II (ISO 7176-5).
48
Publicidad
