Maintenance / Service - Skil F0150711 Serie Manual Original

- after replacing the cutting blade test-run the tool for at
least one minute without load to ensure that the tool is
operating properly
! only use replacement cutting blades of the
correct type (SKIL accessory 2610Z04031)

MAINTENANCE / SERVICE

• This tool is not intended for professional use
• Always switch off tool, disconnect plug from power
source, and ensure that all moving parts have come to a
complete standstill
• Keep all nuts, bolts and screws tight to be sure that the
tool is in a safe working condition
• Regularly check the grass box for wear or damage
• Be aware that during cleaning/maintenance (even
though the tool is switched off) the cutting blade
can still be moved
• Always keep tool and cord clean (especially ventilation
slots H 3)
• Clean the mower after each use with a hand brush and a
soft cloth
- remove compacted grass cuttings from the blade area
with a wooden or plastic implement
! do not use water (especially no high-pressure
sprays)
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skil.com)
TROUBLESHOOTING
• The following listing shows problem symptoms, possible
causes and corrective actions (if these do not identify
and correct the problem, contact your dealer or service
station)
! switch off the tool and disconnect the plug before
investigating the problem
★ Tool does not operate
- no power supply -> check power supply (power cable,
circuit breakers, fuses)
- power supply socket faulty -> use another socket
- extension cord damaged -> replace extension cord
- grass too high -> increase cutting height and tilt tool
★ Tool operates intermittently
- extension cord damaged -> replace extension cord
- internal wiring defective -> contact dealer/service
station
★ Tool leaves ragged finish or motor labours
- cutting height cut too low -> increase cutting height
- cutting blade broken off -> replace cutting blade
- underside of tool badly clogged -> clean tool
★ Cutting blade not rotating
- cutting blade obstructed -> clear obstruction
★ Tool vibrates abnormally
- cutting blade damaged -> replace cutting blade
- cutting blade broken off -> replace cutting blade
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2012/19/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 9 will remind you of this when the need for
disposing occurs
NOISE / VIBRATION
• Measured in accordance with EN 60335 the sound
pressure level of this tool is 83.4 dB(A) (uncertainty K =
1.5 dB) and the sound power level 95.8 dB(A), and the
vibration <2.5 m/s² (triax vector sum; uncertainty K = 1.5
m/s²)
• The vibration emission level has been measured in
accordance with a standardised test given in EN 60335; it
may be used to compare one tool with another and as a
preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintained accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
! protect yourself against the effects of vibration
by maintaining the tool and its accessories,
keeping your hands warm, and organizing your
work patterns
Tondeuse/débroussailleuse
à gazon
INTRODUCTION
• Cet outil est destiné uniquement à la tonte du gazon chez
soi
• Cet outil n'est conçu pour un usage professionnel
• Vérifiez que le conditionnement contient toutes les
pièces présentées dans le schéma 2
• Lorsque des pièces manquent ou sont endommagées,
veuillez contacter votre distributeur
• Lisez attentivement ce manuel d'instruction avant
d'utiliser l'outil et conservez-le pour pouvoir vous y
référer ultérieurement 4
CARACTERISTIQUES TECHNIQUES 1
ELEMENTS DE L'OUTIL 3
A Boulon pour monter la poignée de guide
B Poignée de guide réglable
C Dispositif d'immobilisation du cordon d'alimentation
D Clip du câble
14
0711/0712