Preparing The Unit; Brushing And Flossing - Waterpik Sonic-Fusion SF-01 Manual De Instrucciones

6
PREPARING THE UNIT / BRUSHING AND FLOSSING

Preparing the Unit

Powering the Unit
Plug the cord into an electrical outlet. If the outlet is controlled by a wall switch, be
Click sure it is turned on.
Attaching the Brush Head to the Power Handle
Brus h Brus h
Position the brush head on the power handle as shown. Press firmly until it clicks into
Floss Floss
place. To remove, firmly pull the brush head to separate it from the power handle.
Click
Attaching the Power Handle to the Hose
Position the power handle onto hose in the base. Press the power handle firmly onto
the hose attachment until it clicks into place. To remove, simply press the round
Brush
Floss button on the back side of the power handle.
Charge
Charging the Sonic-Fusion®
Charge for at least 20 minutes before first use by placing the handle on the charging
base. For a full charge, leave the handle on the charging base for at least 4 hours. A
full charge should last 14 uses with a duration of 2 minutes each. If the toothbrush
is to be stored for an extended period of time (six months or more), be sure to fully
Bru sh
charge it (at least 4 hours) prior to storage.
Flo ss
Charge Lights
Toothbrush charge indicator lights will indicate level of battery charge for
approximately 10 seconds after removal from the charging base and after use, and
Brus h
will then turn off. If only the bottom light is lit, then recharging is recommended to
Floss
ensure uninterrupted use.
Wireless Connection Light
Blue
Blue light indicates the flosser base unit is communicating via Wireless
Light
Communication and is "Ready" for activation via FLOSS button.
Preparing the Reservoir
Fill
Remove reservoir and open hinged lid. Fill the reservoir with warm water. Close the
lid and replace the reservoir on the base and press firmly.
Prime Unit (First Time Use Only)
Set pressure control dial on base to high (pressure setting No. 10), point the handle
Floss and brush head into sink. Press the FLOSS button to turn water ON.
After water flows from the nozzle, press the FLOSS button to turn water OFF.
Brushing
Place the brush head in your mouth before pressing the BRUSH button.
Recommended Technique
For best results, position brush along gumline at a 45-degree angle. Press the BRUSH
Brush
button to turn the brush ON. Use light pressure and move the toothbrush slowly
allowing for the sonic action to clean each tooth individually. Brush can be easily
disconnected from the hose if desired (See diagram on product description page).
Quad Timer
30 sec.
The Sonic-Fusion® will create a short pause every 30 seconds to remind you to move
30 sec. to the next section of your mouth. You will brush the outside of the teeth for 30
seconds and then the inside for 30 seconds. This will be repeated on the other arch
for a total of 2 minutes to clean all teeth.
30 sec.
2-Minute Timer
The brush will automatically shut off after 2 minutes of run time.
30 sec.
Water Flossing
Always place the brush head in your mouth prior to pressing the FLOSS button. Lean
over the sink and slightly close lips enough to prevent splashing while still allowing
water to flow from mouth into sink.
Adjusting the Pressure Setting
Adjust
Turn the water flosser pressure control dial on the base of the unit to the lowest
setting (pressure setting No. 1) for first-time use. Gradually increase pressure over
time to the setting you prefer – or as instructed by your dental professional.
Recommended Technique
For best results, start with the back teeth and work toward the front teeth. Direct
Floss
the brush head so that the water flosser nozzle is angled slightly toward the
gumline. Move the brush head along the gumline pausing briefly between each tooth
to allow water to clean between teeth. Continue until you have cleaned the inside
and outside of both the upper and lower teeth. When finished, empty any liquid left
in the reservoir.
NOTE: If you used mouthwash or any other solution besides water, see "Using
Mouthwash and Other Solutions" section.
Concurrent Brushing & Flossing
Floss
The unit is designed to allow you to brush and water floss at the same time. After
completing a brushing cycle, simply press the FLOSS button to start the Flosser and
follow the recommended technique from the Water Flossing section.
7