Phoenix Contact MCR-FLP-D-T-2SP-24 Manual Del Usuario página 18

1 Safety instructions and warnings ................................................................................. 4
1.1 Use according to the intended purpose ........................................................ 4
2. Technical Data
2.1 Miscellaneous Data ......................................................................................................... 5
2.2 Electrical Data .................................................................................................................. 5
2.2.1 Power Supply ..................................................................................................... 5
2.2.2 Inputs ................................................................................................................... 5
2.2.3 Outputs
2.3 Mechanical Data .............................................................................................................. 7
2.4 Environmental conditions ................................................................................................ 7
2.5 Delivery .............................................................................................................................. 7
2.6 Order Code ........................................................................................................................ 7
3. Mounting ........................................................................................................................... 8
4 Electrica Connections ...................................................................................................... 9
4.1 Measuring input ............................................................................................................... 9
4.2 Control Inputs and Auxiliary Signals ............................................................................10
4.3 Power Supply and Outputs .............................................................................................10
5 Parameter Setup ..............................................................................................................11
5.1 Parameter mode ...............................................................................................................11
5.2 Parameter input for actual measured value ..............................................................12
5.3 Select range for the input signal ....................................................................................12
5.3.1 Thermocouples ........................................................................................................12
5.3.1.1 Select type of thermocouples..............................................................12
5.3.1.2 Select display unit .................................................................................12
5.3.1.3 Cold junction compensation .................................................................12
5.3.1.4 Set external cold junction compensation .........................................14
5.3.1.5 Correction value ....................................................................................14
5.3.2 Resistance Measurement ......................................................................................14
5.3.2.1 Select measuring mode ........................................................................14
5.3.2.2 Measurement range ..............................................................................15
5.3.2.3 Display unit (Pt100/Pt1000) ...................................................................15
5.3.2.4 Correction value (Pt100/Pt1000) ..........................................................15
5.3.2.5 Decimal point (400Ω/4000Ω) ................................................................16
5.3.2.6 Changing the scaling slope (400Ω/4000Ω) .......................................16
5.3.3 Input range 0 ... 100 mV DC ...................................................................................16
5.3.3.1 Decimal point for displayed value ......................................................16
5.3.3.2 Changing the scaling scope ................................................................16
5.3.4 Input range -100 ... +100 mV DC ...........................................................................17
5.3.4.1 Select decimal point .............................................................................17
5.3.4.2 Changing the range limits .....................................................................17
5.3.4.3 Changing the scaling scope .................................................................18
Page 2
5.4 Setting the scaling slope ................................................................................................ 14
5.4.1 Enter the number of scaling points ..................................................................... 20
5.4.2 Define the first scaling point ............................................................................... 20
5.4.3 Define the second scaling point .......................................................................... 20
5.4.4 Define additional scaling point ............................................................................ 20
5.5 Alarms/Alarm Outputs
5.5.1 Alarm 1/Output 1 ............................................................................................... 21
5.5.1.1 Alarm 1 off/on .................................................................................. 21
5.5.1.2 Select mode for output threshold 1 ............................................. 21
5.5.1.3 Hysteresis for threshold 1 ............................................................. 22
5.5.1.4 Reset Latch signal at output 1 ..................................................... 23
5.5.1.5 Select signal form for output threshold 1 ..................................23
5.5.2 Alarms 2/Output 2 ............................................................................................. 24
5.5.2.1 Alarm 2 off/on .................................................................................. 24
5.5.2.2 Select mode for output threshold 2 ............................................. 24
5.5.2.3 Hysteresis for output 2 ..................................................................24
5.5.2.4 Reset Latch signal at output 2 ...................................................... 25
5.5.2.5 Select signal form for output threshold 2 ...................................25
5.6 MIN/MAX value acquisition .............................................................................................25
5.6.1 Monitor maximum value ....................................................................................... 25
5.6.1.1 Reset maximum value ......................................................................... 26
5.6.2 Monitor minimum value ........................................................................................ 26
5.6.2.1 Reset minimum value .......................................................................... 26
5.7 Mains Hum Filter ...............................................................................................................26
5.8 Setting Default Values....................................................................................................... 27
5.9. End of setup...................................................................................................................... 27
5.10. Check / alter parameters ............................................................................................... 27
6 Operation ........................................................................................................................... 28
6.1 Switching over the display during operation ............................................................. 29
6.2 Setting the limits during operation ............................................................................... 30
6.3 Resetting the MIN/MAX value ...................................................................................... 30
6.4 Display Hold ...................................................................................................................... 31
Page 3