Publicidad
Idiomas disponibles
Idiomas disponibles
PRE-DRILLED
SCREW HOLE
TRUCK BODY
SELF TAPPING
SCREW
BEDLINER
P/N 12490553
PRE-DRILLED
SLOTTED HOLES
(5 LOCATIONS)
TIE-DOWN ACCESS
TIE-DOWN PLUG
HOLES IN BEDLINER
PRE-DRILLED HOLE
PUSH-IN STYLE FASTENER
Plug Removal:
8VH ¿QJHU WDE RQ SOXJ IRU UHPRYDO IURP DFFHVV KROH
DO NOT USE THE TETHERS TO REMOVE PLUGS. DAMAGE TO THE TETHERS AND FASTENERS MAY OCCUR.
Tailgate Cover Installation:
Bed Liner and Tailgate Liner
ALL INFORMATION WITHIN
DATE
ABOVE BORDER TO BE PRINTED
EXACTLY AS SHOWN ON 8.5 x 11
WHITE 16 POUND NON-BOND
RECYCLABLE PAPER.
PRINT ON BOTH SIDES, EXCLUD-
ING TEMPLATES.
TO BE UNITIZED IN ACCORDANCE
WITH GM SPECIFICATIONS.
P/N 12490553
SELF-TAPPING
SCREW
PLASTIC
BEDLINER
METAL TRUCK BOX
P/N 11612239
TAILGATE
FASTENER SCREW
(8)
P/N 12490553
SELF TAPPING
SCREW
(2)
REVISION
4. 3UHVV WKH EHGOLQHU ¿UPO\ DJDLQVW WKH WUXFN ERG\ DW WKH UHDU VLGHZDOOV 8VLQJ
a center punch, carefully mark the screw locations in the center of both of
the pre- drilled holes (1 each side) in the bedliner. Position the self drilling
screws at the marked locations. Fasten the screws to the truck box wall with
a power screwdriver. DO NOT OVER TIGHTEN BECAUSE THE SCREW
THREADS CAN BE STRIPPED EASILY.
5. 3UHVV WKH EHGOLQHU ¿UPO\ DJDLQVW WKH WUXFN ERG\ 8VLQJ D FHQWHU SXQFK FDUHIXOO\
mark the screw locations in the center of the remaining pre-drilled holes in
the front wall of the bedliner. Position the self drilling screws at the marked
locations. Fasten the screws to the truck box wall with a power screwdriver
in the sequence shown. DO NOT OVER TIGHTEN BECAUSE THE SCREW
THREADS CAN BE STRIPPED EASILY.
6. Install four (4) tie-down plugs into tie-down access holes. Install plugs by
pressing around the outside of the plug until seated. Rotate center attachment
cord to align the hole at the loose end of the cord with the pre-drilled hole in
the bedliner. Insert one push-in style fastener through the hole at the loose
end of the attachment cord and into the pre-drilled hole in the bedliner. Press
¿UPO\ LQWR SODFH
7. Continue installing push-in style fasteners in tie-down covers and into bedliner
sidewalls until all tie-down access covers have been completed.
1. Remove 8 existing factory installed screws from tailgate latch plate and
discard.
2. Center plastic tailgate cover on truck tailgate. Insert and tighten tailgate
fastener screws provided in hardware kit in the holes of tailgate.
3. Using a center punch carefully mark the screw location in the center of
a precut slot. Position self-drilling screw at the marked location. Fasten
the screw to the tailgate with a power screwdriver. DO NOT OVER TIGHTEN
BECAUSE THE SCREW THREADS CAN BE STRIPPED EASILY.
4. Repeat step 3 in the remaining slot location.
REV 25MR13
AUTH
DR
TITLE
PART NO.
6200 Grand Pointe Dr., Grand Blanc, MI 48439
22879302
PART NO.
INSTALLATION INSTRUCTIONS
Bed Liner and Tailgate Liner
22879302
2
9
SHEET
OF
2
9
SHEET
OF
Publicidad
