Using The Menu - IMG STAGELINE CUBE-630/RGBW Manual De Instrucciones

DMX
OUT
➍
with a 120 Ω resistor (> 0 .3 W): Connect a
DMX terminating plug (e . g . DLT-123 from
IMG STAGELINE) to the output jack .
6 Operation
WARNING To prevent damage to your
eyes, never look directly into
the light source for any length
of time .
Please note that stroboscope effects and fast
changes in lighting may trigger epileptic sei-
zures with photosensitive persons or person
with epilepsy!
Important: Prior to operation, make sure that
the lock (1) of the rotary arm is disengaged
(lever in left position); otherwise, the unit may
be damaged .
Insert the blue Powercon plug of the mains
cable supplied into the Powercon jack (5) and
then turn it clockwise until it locks . (To dis-
connect the cable from the unit, pull back
the safety latch on the plug, turn the plug
counter-clockwise and remove the plug from
the jack .) Then connect the mains plug of the
cable to a mains socket (230 V/ 50 Hz); the unit
will be switched on when connected to the
power supply . To switch off the unit, discon-
nect the mains plug from the mains socket .
Note: Never connect or disconnect a Powercon plug
while voltage is applied . Always make the Powercon
connection before making the mains connection .
When disconnecting, always disconnect the mains
connection before disconnecting the Powercon con-
nection .
Once set into operation, the unit will perform
a reset (reset of the motor control); when the
reset is completed,
DMX OK
the display (2) . The operating mode of the
DMX- DMX-controlled
controller unit
DMX DMX DMX
output input output
➏
Operation with a DMX controller
4 5
230V~/
FUSE 50Hz
DMX
IN
6
unit after the reset depends on its settings
and connections:
a) When the unit receives a DMX signal from
a DMX controller, the unit is set to be
controlled via a DMX controller . On the
display,
b) When the unit receives a DMX signal
from a master unit, the unit is in the
slave mode (information with regard to
the master / slave mode:
Mast Mode
appear .
c) When no DMX signal is received and the
menu item
Blackout
the LEDs are switched off and the
moving head is in its home position .
On the display,
d) When no DMX signal is received and
the menu item
to
Auto
mode (automatic show program) . On the
display,
will appear .
e) When no DMX signal is received and the
menu item
, the unit is in the sound mode
Sound
(music-controlled show program) . On the
display,
In each operating mode, the lower line of the
display will indicate the DMX address .
When the menu item
has been set to
display will be switched off after 30 seconds
if none of the buttons (3) is pressed . To switch
the display on again, press any button .
will appear on
DMX-controlled DMX-controlled
unit unit
DMX DMX DMX DMX
input output input output
will appear .
DMX OK
☞ chapter 7 .2,
) . On the display,
DMX OK
has been set to
DMX Lost
(factory setting) or
Hold
will appear .
No DMX
has been set
DMX Lost
, the unit is in the automatic
and the program number
Auto
has been set to
DMX Lost
will appear .
Sound
Display BkLight
(factory setting), the
Off
DMX-controlled
unit
DMX DMX
input output
DMX terminating plug
( if required )
A
B
A
➎

7 Using the Menu

Use the buttons MENU, DOWN, UP and
ENTER (3) to operate the menu . The menu
structure can be found on page 2 .
Buttons Functions
– to call up the menu
– to go back to the previous menu level
MENU
and, when the highest menu level
has been reached, to exit the menu
– to navigate through the menu
DOWN
will
(upwards / downwards)
and UP
– to set a menu item
– to call up a menu item or to activate
the function of a menu item
,
– to confirm / save the setting of a menu
item and to return to the previous
ENTER
menu level
Exception: Settings in the operation
mode
Manual Control
ter 7 .2) will not be saved .
The menu will be automatically exited after
approx . 30 seconds when no button is
pressed .
7.1 Setting the DMX address
–
DMX Address
For separate control of all DMX units by means
of a DMX controller, each unit requires a start
address of its own . The start address refers to
the first DMX channel of the unit (for start ad-
dress 10, for example, the first channel of the
unit will be operated via control channel 10
of the controller) . The other DMX channels
of the unit will be automatically assigned to
the subsequent addresses .
Example: For the 35-channel mode and start ad-
dress 10, the channels 1 to 35 are assigned to the
addresses 10 to 44 . The address 45 is the next start
address available for the subsequent DMX-controlled
unit .
A
A
B
B
B
A
☞
( chap-
–
9