Descargar Imprimir esta página

Juliana Premium Instrucciones De Montaje página 4

Ocultar thumbs Ver también para Premium:

Publicidad

GB
May we congratulate you on your new greenhouse
Dear Customer!
DEAR CUSTOMER
Congratulations on purchasing your new
The assembly of your new house requires
greenhouse. It is important that you follow these
a bit of technical knowledge. However, it is
assembly instructions step-by-step.
important that the assembly instructions are
followed strict-ly. The assembly instruction
The assembly instructions are a combination of text
is a combination of text and illustrations. The
and illustrations. The profiles are packed in separate,
profiles are packed in separate numbered packs
numbered packs corresponding to their order of use
corresponding to the order in the assembly
in the instructions. Assemble one pack at a time. All
nuts, bolts and fittings are contained in a Box.
instruction. Erect one pack at a time. All nuts
Each pack is specified in separate lists of
and bolts and fittings are found in bag No. 0
components.
(specified on page 12). Each pack is specified in
All detailed illustrations are marked with the
separate lists of components.
following symbols:
All detailed illustrations are marked with
symbols:
Seen from the inside
Seen from the outside
Seen from inside
Seen from outside.
SOME SAFETY PRECAUTIONS
Assembly must only be carried out in dry and
calm weather.
Precautions.
Always wear work gloves when installing the
Assembly must only be carried out in dry
glazing. Greenhouse glass has sharp edges,
and calm weather.
especially if it breaks.
Always use working gloves while glazing.
Assistants and especially children must be
Greenhouse glass has sharp edges,
warned that broken glass is dangerous. Pick
especially if the glass breaks.
up all broken glass at once and remove it with
Assistants and especially children must be
care.
We recommend that you wear protective
warned that broken glass is an element of
glasses while fixing the spring wire clips.
danger. Pick up broken glass at once and
Any ladders that are used must be placed on a
remove it with care.
level surface.
We recommend to use protective glasses
It is essential to have an assistant available.
while fixing the spring wire clips.
Place the ladder on a level support.
TOOLS
It is essential to have an assistant.
Assembling the greenhouse requires tools.
References
FOUNDATIONS
No base is included with this product. However, an
The column marked
indicates the
original base is available separately. This base is easy
page(s) on which the component is used.
to construct and will guarantee you a stable base for
your greenhouse.
Page 13:
If you construct your own base, the specified
Foundation
measurements must be external measurements.
The base is not included in this delivery.
The holes must be dug out to below the frost line.
However, an original base can be bought
Place the assembled base with anchor legs over the
separately. It ensures you a stable and easy to
holes so the anchor legs fit into the holes; it takes
about 75 litres of concrete to fill up the holes.
build base.
Make sure the base is completely level and square.
If you make your own base the measurements
To square the base, make sure the two diagonal
indicated must be external measurements.
measurements are identical.
If you buy an original base you furthermore
The width of the front and back gables must also be
need about 75 litres of concrete and 6/8
identical..
plastic-/concrete pipes of about 800 mm which
are placed in a non-freezing depth for the
ATTACHMENT TO THE BASE
If you construct your own base, you must drill holes
fastening of the corner and middle anchors.
(Ø7) in the ground frame between all the vertical
The base must be 100% level and square; the
profiles. The greenhouse must then be secured to
latter is ensured by checking that the two
the base using screws (A).
diagonal measurements are equal.
If you use an original base, the greenhouse must be
secured to each vertical bar as shown on drawings
Tools
B/C.
The mounting of the greenhouse requires the
tools shown on page 12.
ORDER OF ASSEMBLY
Place the components as shown on the illustration
and assemble in the order shown in the pictures. Do
Page 14-27:
not tighten the nuts fully until the entire sub-frame
Place the components as shown on the
has been assembled.
illustration and assemble in the order shown
in the pictures. Do not tighten the nuts
DOORS AND WINDOWS
completely until the front gable construction
For easier assembly, we recommend that you oil the
has been assembled.
screws for the doors. The glass or polycarbonate for
the door(s) and windows must be fitted at the same
time as the profiles.
Page 13:
FITTING OF GLASS/POLYCARBONATE
Important before assembly!
(Fastening to the base).
Make sure that the gables and sides are level
When constructing your own base you have
and square and that door(s) and window(s) are
to drill holes (7 mm) in the ground frame
functioning perfectly.
between all the vertical frames, the greenhouse
is then fastened to the base with screws (A).
The best order of assembly for the glass or
Using an original base the greenhouse is
polycarbonate is as follows:
fastened to each vertical bar as shown on
Windows - Roof - Doors - Gables - Sides
drawing B/C.
GLASS INSTALLATION
Glass installation (illustrations 1 to 8)
Page 24-27:
Degrease the sheets and frames with ethanol.
For an easier assembly we recommend that you
Start glazing from the bottom, one pane at a time.
oil the screws for the doors.
Apply a 3mm silicone bead around the vertical
frames as indicated (the dotted lines on the
Fitting of glass/polycarbonate
illustration). (A 3mm bead of silicone is sufficient to
Important before glazing!
ensure maximum adhesion). If you use more silicone
than recommended, extra tubes can be purchased.
Make sure that gables and sides are level and
Spring wire clips and glass-holders must be fitted as
square, and that door(s) and window(s) are
shown.
functioning perfectly.
X = Spring wire clips, > = Glass-holders
Best order of assembly:
If you accidentally break a pane, carefully pull the
1) Windows – 2) Roof – 3) Doors – 4) Gables
broken glass outwards and loosen the silicone using
– 5) Sides
a sharp craft knife.
Clean the profile completely before inserting a new
pane of glass.
Page 30-33:
Glazing (illustration 1 to 8)
POLYCARBONATE INSTALLATION
Degrease the sheets and frames with spirit.
The type designation states the length in
Start glazing from below, one glass at a time.
millimetres. If adjustment is necessary, use a fine-
Apply a 3 mm silicone line on the vertical
tooth saw.
frames where indicated (dotted lines on
NB! To avoid the growth of algae, prevent the
the illustration). (A 3 mm line of silicone is
polycarbonate sheets from coming into contact with
the ground by resting them on a sheet of cardboard.
sufficient to obtain maximum attachment). If
you do use more than recommended, you can
A-strips.
buy extra tubes.
Insert the sheet into the bottom strip, bend the
sheet slightly outwards and insert it into the top
Spring wire clips and glassholders are to be
strip.
fitted as shown.
X = Spring wire clips, > = Glassholders
M-strips.
Place the upper part of the strip under the
aluminium profile along the full length of the sheet
In case of broken glass carefully pull it
and then click the strip into position from above.
outwards and loosen the silicone by means of a
sharp craft knife.
U-strips.
Clean the profile completely before inserting a
Fit the strip to the sheet and adjust the length.
new pane of glass.
If desired, the sheets may be sealed against insects.
Page 34-37:
Seal the top using aluminium tape or silicone. The
Mounting of polycarbonate
bottom should only be sealed with air-strip tape to
allow condensation to escape (available from your
The illustrations at the bottom of page 34/36
local dealer).
show where to mount the polycarbonate plates
and lists. The type indication states the length
in mm. A possible adjustment is made by
means of a fine-tooth saw.
NB! To avoid the formation of algae the
polycarbonate sheets must not come into
contact with the ground. Rest them on a piece
of cardboard.
A-lists are mounted as shown on page 35/37.
Put the sheet into the bottom list, bend the
sheet slightly outwards and put it in the top list.
M-lists are mounted as shown on page 35/37.
Place the upper part of the list under the alu.
profile in the whole length of the sheet and
hereafter click on the list from above.
4
Your greenhouse is now fully assembled. However,
Sealing of the polycarbonate sheets
please note the following:
The sheets may be sealed against insects.
Close the top end off with alu-tape or silicone.
MAINTENANCE
The bottom only with airstrip tape to let
Grease the doors (hinges and locks).
condensation out (available at your local
Keep the gutters free from leaves, etc.
dealer).
Adjust the windows as necessary.
Replace any broken glass.
Clean the greenhouse with disinfectant before
Now your greenhouse is completely assembled.
and after the growing season.
However, please notice the following:
WINTER PROTECTION
Maintenance
If you anticipate snow during the winter, we
Grease doors (hinges and lock).
recommend the following winter precautions:
Clean the gutter for leaves, etc.
Support the apex of the roof in the middle.
Adjustment of windows.
Remove any deep snow from the roof.
Replacement of broken glass.
Take precautions to prevent snow falling from
a tree or roof, for example.
Clean the house with disinfectant before
Remove the cylinders for the automatic
and after the growing season.
window openers, if fitted (optional extras).
Secure the door(s) and window(s) to prevent
Winter Protection
wind damage to the greenhouse.
In areas with occurrence of snow we
recommend the following winter protection:
WATER AND CONDENSATION
Support the roof ridge at the centre of the
Please note that your greenhouse is not like a
house.
conservatory, for example, and that you should
therefore be aware that the greenhouse may leak
Remove greater snow loads from the roof.
during or after precipitation and that condensation
Take precautions against snow falling
will occur on the inside of the greenhouse. Good
down from for instance a tree or a roof.
ventilation will help prevent condensation.
Dismount the cylinders for the automatic
window openers, if any (optional extras).
INSURANCE
Secure door(s) and window(s) preventing
Please note that not all insurance companies cover
wind damage to the house.
greenhouses automatically. Please contact your
insurance company to ensure that your greenhouse
is covered.
Insurance
Please note that not all insurance companies
GUARANTEE
cover glasshouses automatically. Please
Juliana greenhouses are covered by a 12-year
contact your insurance company to ensure an
guarantee, which covers the replacement or repair
insurance coverage.
of faulty parts. The guarantee does not cover
polycarbonate, glass, transport, assembly, freight,
Guarantee
etc.
Juliana grants a guarantee of 12 years which
Juliana greenhouses are covered by a two-year
warranty on painted parts, where fitted. Note that
covers replacement of faulty parts. The
marks on the paint may occur due to suspension of
guarantee does not cover polycarbonate, glass,
the profiles.
transport, assembly, freight etc.
The guarantee will be void if the greenhouse is not
Juliana grants a guarantee of 2 years on painted
assembled in accordance with these instructions.
parts, if any. Note that marks in the painting
may occur due to suspension of the profiles.
COMPLAINTS
The guarantee is invalid if the greenhouse is
All our greenhouses are built to the highest quality
not assembled according to these instructions.
standards. However, should you experience any
problems, please contact your dealer at once. When
describing the defect, please state the greenhouse
Complaints
model, the component number.
All our greenhouses are built to high standards
of quality. However, should a complaint
Congratulations on your new greenhouse, which we
occur please contact your dealer at once.
hope will bring you a lot of pleasure for many years
Remember to specify the defect by indicating
to come.
the greenhouse model and number of the
component and the quality control number.
Yours sincerely,
Juliana Drivhuse A/S
USA

Publicidad

loading