Publicidad
Idiomas disponibles
Idiomas disponibles
PROGRAMMING
Before programming you must:
Move the jumper J1 on the back of the
push- button panel from A to B; the
display shows "Programming / type:
".
Dial the programming code ( see table )
and press
to confirm.
After you programme each single
code, bring the jumper J1 back to A.
To exit and access the 4-digit
programming codes you must move
the jumper J1.
Positions of jumper J1
A = operation mode
B = programming mode
A
B
J1
J1
Table of programming codes
0000 Entry of codes for door lock /
address P1 / address PE
0001 Entry-modification-deletion of
names
0002 Language selection
0003 System programming
0004 Entry of display initial text
0005 Loading names from PC
0006 Ordering names
Entry of codes for door lock / address
P1 / address PE (code 0000)
Enter the code 0000 to access the "entry
of door lock codes" mode. The display
shows "PASSWORD 0 /
Dial the first opening code on the
keypad, for example 7890; the display
shows "PASSWORD 0 / 7890".
Press
; the display shows
"PASSWORD 1 /
".
Dial the second opening code on the
keypad, for example 1234; the display
shows "PASSWORD 1 / 1234".
Press
; the display shows
"PASSWORD 2 /
".
Repeat the operation to enter a
maximum of 16 codes. When you
press
to confirm the last code
(PASSWORD 15) you enter the "entry
of address P1 code" mode
automatically. You can memorise the
number of the internal station that can
be called directly by pushing a button
connected between terminals P1 and
-.
Press
; the display shows "P1 /
1000".
Press
to delete the code shown on
the display and enter the number of the
internal station you want to enable for
the direct call function.
Press
"entry of address PE code"; the
display shows "PE / ". You can enter
the code for the external station
address. The push-button panels can
be coded with numbers from 9950 to
9979.
Dial the code and press
You go back to the "entry of door
lock codes" mode. The display shows
the
PASSWORD
( PASSWORD 0 / internal station)".
To exit programming bring the jumper
J1 back to the original position (from
B to A).
Note. To delete the password and the
address associated with P1 and PE
press
and then press
Entry / modification / deletion of
names (code 0001)
You can enter 32 characters, of which 28
characters for the name and the last 4
characters on bottom right for the internal
station number. When searching for
characters, the display shows upper-
case letters, low-case letters, numbers,
characters . <> and space in a sequence.
Enter the names from top down and from
left to right. You must enter a number in
".
the last space on bottom right to save the
name (see "deleting a name"). The
push-button panel reorders the list in
alphabetical order every time you enter
and confirm a name.
Function of buttons
Hold this button pressed to scroll the
list of existing names
Hold this button pressed to move the
cursor to the name characters
Hold this button pressed to scroll
down the list of characters
Hold this button pressed to scroll up
the list of characters
to confirm and go to the
to confirm.
0
code
again.
Entry of names
Move the jumper J1 from A to B.
Enter the code 0001; the display shows
the first name. The display is empty if
no codes are programmed.
Press
or
to select the character
for the first cell; press
second cell; press
or
the character for the second cell;
continue until you have entered the
complete name with code. Press
after you have entered the number in
the last cell on bottom right; the display
shows "STORE USER / YES < > NO ";
press
to confirm; press
the name.
If confirmed, the display shows the
second name. The display is empty if
no names are programmed.
Once you have confirmed the last
name, bring the jumper back to the
original position (from B to A). The
display shows " waiting" and an
automatic status bar. Normal operation
is restored after a few seconds and
the display shows the initial text (see
" Operation").
Notes. Once you have entered 250
names the display shows " waiting" and
an automatic status bar. After a few
seconds
the
display
"Programming / type: " and you can
continue with programming.
You can enter 2 or more names with the
same call number (i.e. different family
names in the same apartment).
Modification of names
Press
to search for the name you
want to modify; (hold the button
pressed for quick searching).
Press
to go to the character you
want to modify.
Select the character with
(backward).
Repeat the operation until you have
completed the name modification.
Once you have completed the
modification, hold
pressed until the
display shows "STORE USER / YES
< > NO" Press
to confirm or
modify the name again.
Enter a space to delete a letter.
to go to the
to select
to modify
shows
(forward)
to
11
Mi 2293/1
Publicidad
