Safety Instructions; Basic Information Concerning Safety; General Safety Rules; Proper Organization Of The Work Area - Hilti PR 3-HVSG Manual De Instrucciones

On the type identification plate
Laser Class 2 product. Do not look into the beam.

2 Safety instructions

2.1 Basic information concerning safety

Read all safety warnings and all instructions. Failure to
follow the warnings and instructions may result in electric
shock, fire and/or serious injury. Save all warnings and
instructions for future reference. The term "power tool"
in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.

2.2 General safety rules

a) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
b) Do not render safety devices ineffective and do
not remove information and warning notices.
c) Keep laser tools out of reach of children.
d) Failure to follow the correct procedures when open-
ing the tool may cause emission of laser radiation in
excess of class 2. Have the tool repaired only at a
Hilti Service Center.
e) The plane of the laser beam should be well above or
well below eye height.
f) Take the influences of the surrounding area into
account. Do not use the tool where there is a risk
of fire or explosion.
g) (Statement in accordance with FCC §15.21):
Changes or modifications not expressly approved
by the manufacturer can void the user's authority to
operate the equipment.
h) Check the condition of the tool before use. If the
tool is found to be damaged, have it repaired at a
Hilti service center.
i) The user must check the accuracy of the tool
after it has been dropped or subjected to other
mechanical stresses.
When the tool is brought into a warm environment
j)
from very cold conditions, or vice-versa, allow it
to become acclimatized before use.
k) Make sure that the tool is mounted securely when
adapters or accessories are used.
All manuals and user guides at all-guides.com
Location of identification data on the tool
The type designation and serial number can be found on
the type identification plate on the tool. Make a note of
this data in your operating instructions and always refer
to it when making an enquiry to your Hilti representative
or service department.
Type:
Generation: 01
Serial no.:
l)
m) Although the tool is designed for the tough condi-
n) Although the tool is protected to prevent entry
o) Check the tool before using it for important meas-
p) Check the accuracy of the measurements several
q) Ensure that the workplace is well lit.
r)
s)

2.3 Proper organization of the work area

a) Secure the area in which you are working and
b) Avoid unfavorable body positions when working
c) Readings taken in the vicinity of reflective objects or
d) Ensure that the tool is set up on a steady, level
e) Use the tool only within its specified limits.
f)
Keep the laser exit aperture clean to avoid meas-
urement errors.
tions of jobsite use, as with other optical and elec-
tronic instruments (e.g. binoculars, spectacles,
cameras) it should be treated with care.
of dampness, it should be wiped dry each time
before being put away in its transport container.
uring work.
times during use of the tool.
Avoid touching the contacts.
Maintain the machine carefully. Check for mis-
alignment or binding of moving parts, breakage
of parts and any other condition that may affect
the machine's operation. If damaged, have the
machine repaired before use. Poor maintenance is
the cause of many accidents.
take care to avoid directing the beam towards
other persons or towards yourself when setting
up the tool.
from ladders. Make sure you work from a safe
stance and stay in balance at all times.
surfaces, through panes of glass or similar materials
may produce incorrect results.
surface (not subject to vibration).
Use the tool and its accessories etc. in accord-
ance with these instructions and in the manner
intended for the particular type of tool. Take the
working conditions and the work to be performed
into account. Use of tools for applications differ-
en
13