Descargar Imprimir esta página

BGS technic 63500 Instruction Manual página 7

Comprobador digital de carga de batería

Publicidad

Idiomas disponibles

Idiomas disponibles

1. Keep work area clean. Cluttered areas invite injuries.
2. Observe work area conditions. Do not use the Battery Tester in damp or wet locations. Don't
expose to rain. Keep work area well lighted. Do not use electrically powered tools in the presence
of flammable gases or liquids.
3. Keep children away. Children must never be allowed in the work area. Do not let them handle the
Battery Tester.
4. Store idle equipment. When not in use, products must be stored in a dry location to inhibit rust.
Always lock up products and keep out of reach of children.
5. Use the right product for the job. Do not attempt to force a small Battery Tester to do the work of
a larger industrial Battery Tester. There are certain applications for which this Battery Tester was
designed. It will do the job better and more safely at the rate for which it was intended. Do not
modify this Battery Tester and do not use this Battery Tester for a purpose for which it was not
intended.
6. Dress properly. Do not wear loose clothing or jewelry as they can be caught in the Battery Tester.
Protective, electrically non-conductive clothes and non-skid footwear are recommended when
working. Wear restrictive hair covering to contain long hair.
7. Use eye and ear protection. Always wear ANSI approved impact safety goggles. Wear a full face
shield when working with battery acid. Wear an ANSI approved dust mask or respirator when
working around metal, wood, and chemical dusts and mists.
8. Dot overreach. Keep proper footing and balance at all times. Do not reach over or across running
machines.
9. Maintain tools with care. Keep the Battery Tester clean for better and safer performance. Follow
instructions for changing accessories. Inspect product cords periodically, and if damaged, have
them repaired by an authorized technician. The handles must be kept clean, dry, and free from oil
and grease at all times.
10. Disconnect power. Disconnect from battery when not in use.
11. Avoid unintentional starting. Be sure the switch is in the Off position when not in use.
12. Stay alert. Watch what you are doing, use common sense. Do not operate any product when you
are tired.
13. Check for damaged parts. Before using any product, any part that appears damaged should be
carefully checked to determine that it will operate properly and perform its intended function.
Check for alignment and binding of moving parts; any broken parts or mounting fixtures; and any
other condition that may affect proper operation. Any part that is damaged should be properly
repaired or replaced by a qualified technician. Do not use the product if any switch does not turn
On and Off properly.
14. Guard against electric shock. Prevent body contact with grounded surfaces such as pipes,
radiators, ranges, and refrigerator enclosures.
15. Replacement parts and accessories. When servicing, use only identical replacement parts. Use
of any other parts will void the warranty. Only use accessories intended for use with this tool. Do
not operate product if under the influence of alcohol or drugs. Read warning labels if taking
prescription medicine to determine if your judgment or reflexes are impaired while taking drugs. If
there is any doubt, do not operate the product.
16. Maintenance. For your safety, service and maintenance should be performed regularly by a
qualified technician.
17. Beware of hot surfaces. The cables, clamps, and batteries may become hot during use. Avoid
touching without exercising care to avoid harm and injury.
18. Avoid extreme heat. Do not create smoke, flames, or sparks near batteries. Battery acid is
extremely explosive.
19. Pacemaker safety warning. People with pacemakers should consult with their
20. physician(s) before using this product; operation of equipment in close proximity to a heart
pacemaker could cause interference or failure of the pacemaker.
21. Load Switch Warnings. Release the Load Switch before connecting, disconnecting, or rocking
clamps. Do not depress the Load Switch for longer than ten seconds.
SW-Stahl und Werkzeugvertriebs GmbH
L
e
v
e
k r
u
s
r e
t S
a r
s
s
e
6
5
D
4 -
2
8
9
7
R
e
m
s
c
h
e
d i
Tel. +49 (0) 2191 / 46438-0
F
ax +49 (0) 2191 / 46438-40
- E
M
a
: l i
n i
o f
@
s
w
s
a t
l h
d .
e

Publicidad

loading