Adding Gasoline To The Fuel Tank - Ryobi RY802800 Manual Del Operador

Fuel system damage or performance problems resulting
from the use of an oxygenated fuel containing more than
the percentage of oxygenates stated below are not covered
under warranty.

ADDING GASOLINE TO THE FUEL TANK

See Figure 8.
DANGER:
Risk of fire and serious burns: Never remove fuel cap
when unit is running. Shut off engine and allow the unit
to cool at least five minutes. Remove cap slowly.
WARNING:
Gasoline and its vapors are highly flammable and
explosive. To prevent serious personal injury and prop-
erty damage, handle gasoline with care. Keep away from
ignition sources, handle outdoors only, do not smoke
while adding fuel, and wipe up spills immediately.
WARNING:
Always shut off engine before fueling. Never remove fuel
cap or add fuel to a machine with a running or hot engine.
When adding gas to the pressure washer, make sure the
unit is sitting on a flat, level surface and only add fuel
outdoors. If the engine is hot, let the pressure washer cool
for at least five minutes before adding gas. Immediately
replace fuel cap after fueling and tighten until the cap
"clicks." Move at least 30 ft. from refueling site before
starting engine. Do not smoke and stay away from open
flames and sparks! Failure to follow these instructions
could result in a fire and cause serious personal injury.
NOTE: This is a 4-cycle engine. DO NOT mix fuel and
lubricant together.
n Mix fuel stabilizer with gasoline according to fuel stabilizer
manufacturer's directions.
n Before removing the fuel cap, clean the area around it.
Remove the fuel cap.
n Insert a clean funnel into the fuel tank then slowly pour gas-
oline into the tank. Fill tank to approximately 1-1/2 in. below
the top of the tank neck (this allows for fuel expansion).
n Replace fuel cap and tighten until the cap "clicks".
n Clean up any spills before starting the engine.
All manuals and user guides at all-guides.com
OPERATION
STARTING AND STOPPING THE PRESSURE
WASHER
See Figures 9 - 11.
Before starting the engine:
n Connect all hoses.
NOTE: Make sure the pressure washer's water intake screen
is in place and unclogged before connecting garden hose.
n Check all fluids (oil and gas).
n Turn on the garden hose then squeeze the trigger to
To start the engine:
n Turn the fuel valve to the OPEN position.
n Put the on/off switch in the ON position.
n Pull choke out to the start position.
n Grasp the starter grip and pull slowly until resistance is felt.
n Let engine run for several seconds, then push choke in.
To stop the engine:
n Put the on/off switch in the OFF position.
n Turn the fuel valve to the CLOSED position.
NOTE: Shutting off the engine will not relieve pressure in the
system. Pull trigger to release water pressure.
Page 11 — English
NOTICE:
Do not run the pressure washer without water supply
connected and turned on, as this may damage the high
pressure seals and decrease pump life. Completely
unwind the hose from its reel or coil and make sure the
hose is not being restricted by tires, rocks, or any other
objects that may lessen or prevent water flow to the
pressure washer.
relieve air pressure; hold the trigger until a steady stream
of water appears.
NOTE: Make sure the faucet is turned on fully and that
there are no kinks or leaks in the hose.
NOTE: If restarting after a brief stop (i.e., after refueling
or moving), leave the choke lever in the RUN position.
Give the starter grip a short, brisk pull to start the engine.
NOTE: Do not allow the starter grip and rope to snap
back after starting; return it gently to its original place.
NOTICE:
Routinely make a visual inspection of the pump and
engine during use. If you notice any lubricant leaking
around the pump or engine seals, stop using the pres-
sure washer immediately. Contact customer service or
a qualified service center for repair. Failure to do so may
cause property damage.