Worx Intellicut WG782 Manual Del Usuario página 13

Cortacesped de bateria 3 in 1
Ocultar thumbs Ver también para Intellicut WG782:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

OPERATION
1. STARTING AND STOPPING
(See Fig. F1, F2, F3)
WARNING! The Blade(17) continues to rotate
for a few seconds after the machine is switched
off. Allow the motor/blade to stop rotating before
switching "on" again. Do not rapidly switch off and
on.
STARTING
1)
Insert Safety Key (6) into the housing of the
switch box (See Fig. F1) .
2)
Slide the Safety Key to the right and hold in
position (See Fig. F2) .
3)
Pull the Switch Lever(2) towards the handle bar
and the mower will start (See Fig. F3) .
4)
Release the Safety Key and begin mowing.
NOTE: The Safety Key will stay in the "on" position as
long as the operator holds the lever tightly against the
handlebar.
STOPPING
Release the Switch Lever and remove the Safety Key.
2. INSTALLING MULCH PLUG (15) (See Fig. G)
1)
Turn the mower off, wait until the blade stops and
remove the Safety Key (6).
2)
Raise the Safety Flap and hold it up.
3)
Slide the mulching insert into the discharge
opening until it is firmly in contact with the deck.
4)
Release Safety Flap and ensure it is properly
closed.
3.REMOVING MULCH PLUG(15) (See Fig. G)
Remove the mulch plug when you desire to either
collect grass or discharge grass from the rear of the
mower.
1)
Shut the mower off, wait until the blade stops
and remove the Safety Key (6).
2)
Raise the Safety Flap (11) and hold it in the up
position.
3)
Grasp the handle on the Mulch Plug then lift
upward and pull it out.
4)
Release the Safety Flap and ensure it is properly
closed.
4. INTELLICUT CUTTING MODE DIAL
SELECTION (See Fig. H)
QUIET MODE
Set the IntelliCut Dial (19) to QUIET mode when
mowing in everyday conditions, removing
approximately 1 inch of grass at a time.
POWER MODE
Set the IntelliCut Dial to POWER mode when cutting
dense or overgrown grass.
3-in-1 Cordless Lawn Mower
All manuals and user guides at all-guides.com
5. BATTERY STATUS LED'S (See Fig. I)
NOTE: The Power Level will indicate the battery
condition when the button on the battery is
pressed.
The Power Level Lights display the battery condition
as follows:
Press the button "POWERTEST" , the power level
light(s) will illuminate.
When the three green lights are illuminated, the
Battery Pack (12) is in a highly charged condition.
When two lights (
in a moderately charged condition.
When only one green light (
battery charge is very low and should be recharged .
Before using your new mower for the first time, it is
recommended that the unit be charged overnight to
ensure that the battery is fully charged.
IMPORTANT
When only one light is illuminated, your battery
is discharged, even though the mower may
still be capable of cutting grass. Continuing to
operate your lawnmower with the battery in
this discharged condition may reduce the life
and performance of your battery.
6. ADJUSTING THE CUTTING HEIGHT (See Fig. J)
Mower blades continue to rotate after the machine
is switched off and a rotating blade can cause injury.
Wait until all machine components have completely
stopped before touching them.
1)
2)
3)
4)
7. GRASS BAG FILLING INDICATOR(4) (See Fig. K)
To alert you that the Grass Collection Bag(5) is full,
the mower provides a Grass Collection Bag Filling
Indicator on the top of the bag.
Empty status: flap floats (a)
Fully status: flap falls down (b)
8. REAR DISCHARGE (See Fig. L)
The mower provides a rear discharge function, so that
) are illuminated, the battery is
) is illuminated, the
WARNING! Before adjusting the mower
height, wait for the mower to completely stop.
The mower was shipped at the lowest cut height
setting.
Before your first use of the mower make sure the
cut height is adjusted..
The lawnmower can be set to 3 cut heights: 2" ,
2.75" , and 3.5" .
Adjust one wheel at a time.
Remove the Battery Pack (12).
Turn mower onto its left side (See Fig. J)
Grip the wheel and pull or push it forward.
Make sure to pull it forward far enough that it
is able to be move up and/or down in the wheel
bracket.
With the wheel in its most forward position slide
it up or down into the desired position.
Repeat the above steps to all four wheels.
13
EN

Publicidad

Tabla de contenido
loading

Tabla de contenido