Machine-Related Safety Instructions; Health Hazard By Dust - Festool ETS 150/3 EQ Manual De Instrucciones

away from moving parts. Loose clothes, jewellery
or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of dust
collection can reduce dust-related hazards.
4 POWER TOOL USE AND CARE
a) Do not force the power tool. Use the correct pow-
er tool for your application. The correct power
tool will do the job better and safer at the rate for
which it was designed.
b) Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must
be repaired.
c) Disconnect the plug from the power source and/
or battery pack from the power tool before mak-
ing any adjustments, changing accessories, or
storing power tools. Such preventive safety mea-
sures reduce the risk of starting the power tool
accidentally.
d) Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool's operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.
in accordance with these instructions taking into
account the working conditions and the work to
be performed. Use of the power tool for opera-
tions different from those intended could result in
a hazardous situation.
h) Keep handles dry, clean and free of oil and
grease. Slippery handles do not allow for safe
handling and control of the tool in unexpected
situations.
5 SERVICE
a) Have your power tool serviced by a qualifi ed
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.

Machine-related safety instructions

– Hold power tools by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed metal
parts of the tool "live" and shock the operator.
– Harmful/toxic dusts can be produced during your
work (e.g. lead-containing paint, some types of
wood). Contact with these dusts, especially inhal-
ing them, can represent a hazard for operating
personnel or persons in the vicinity. Comply with
the safety regulations that apply in your country.
Connect the electric power tool to a suitable ex-
traction system.
To protect your health, wear a P2 protective
mask.
Always wear protective goggles to protect
against sanding hazards.
– Prevent liquid polish from entering the machine.
The penetration of liquid polish into the electric
power tool increases the risk of an electric shock.
– If the power tool is dropped or falls, check for
damage to the machine and sanding pad. Re-
move the sanding pad for closer inspection. Re-
pair damaged parts before using again. Broken
sanding pads and damaged machines can cause
injuries and machine instability.

Health hazard by dust

Various dust created by power sand-
ing, sawing, grinding, drilling and other construc-
tion activities contains chemicals known (to the
State of California) to cause cancer, birth defects or
other reproductive harm. Some examples of these
chemicals are:
• Lead from lead-based paints,
• Crystalline silica from bricks and cement and
other masonry products,
• Arsenic and chromium from chemically-treated
lumber.
The risk from these exposures varies, depending
on how often you do this type of work.
To reduce your exposure to these
chemicals work in a well ventilated
area and use approved safety equip-
ment, such as dust masks that are spe-
cially designed to fi lter out microscopic
particles. Wash hands after handling.
O REDUCE THE RISK OF INJURY,
T
USER MUST READ INSTRUCTION MANUAL.
4