Miche SYNTIUM AXY Manual De Uso Y Mantenimiento página 6

• To the users of more than 85kg weight, Fac Michelin S.r.l. sug-
gests to check the wheels status to the mechanic every two
months or every 1,500km.
• We reccomend using these wheels if you weigh more than
102 Kg
• Salt water environments (as found on winter roads and neat the
seaside) can cause galvanic corrosion on most bike parts. Care-
fully rinse, clean, dry and re-lubricate all exposed parts to avoid
damage, malfunctions and accidents.
• Never wash the parts with pressure-fed water, because water
may penetrate the seals and cause permanent damage to the
internal components. We recommend washing the components
using a sponge, mild soap and water.
HuBs
2
Warning
!
If you have any doubt whatsoever your service-repair ability,
please take your bicycle to a qualified repair shop.
Before any maintenance operations on your wheels, always
wear gloves and protection glasses.
Use original spare parts exclusively provided by
Fac Michelin S.r.l.
When replacing any broken sealed bearings please ensure sealed
bearing correct measure and specification are used.
Rear hub
Right side MICHE 28x15x7 (6902-2RS) MICHE 24x12x6 (6901-2RS)
Left side MICHE 24x12x6 (6901-2RS) MICHE 24x12x6 (6901-2RS)
Free wheel MICHE 24x12x6 (6901-2RS)
The hubs are easy to maintain. To do it, proceed as follows:
frONT HuB
• Insert two keys (A) in the extremity of the hubs (Pic. 1), and turn
them counterclockwise.
• While you are taking out the mobile side, take out from the oppo-
site side the complete pin.
• Once you take out the pin from hub' s body, you could, if it is
necessary, change the bearings.
To reassembly it:
• Put the pin into the hub' s body and lock with power the mobile
side with a torque of 15 Nm. If necessary, adjust the hub by wor-
king on the ring (D):
• Unlock the grub screw (E) with a key (B) (Pic1).
• Turn the ring clockwise to drop the sliding, and counterclockwi-
se to raise the sliding. Lock the grub screw (E).
• Check the sliding of the wheel.
Please check that the hub is correctly tightened and closed,
failure to do so could lead to a serious or fatal accident.
Warning
!
Use original spare parts exclusively provided by Fac Michelin S.r.l.
Any modification or alteration (also graphic) of the product with
non-original spare parts or spare parts not delivered directly by
Fac Michelin S.r.l., involves the expiration of the guarantee.
reAr HuB
• Insert two keys (A) in the extremity of the hubs (Pic. 2, and turn
6 SYNTIUM AXY / MICHE.It
Front hub
them clockwise.
• Once you take out the pin from hub' s body, the free wheel body (C)
stays attached with his pawls (Pic. 2).
• Clean carefully the pawls then put some low-density grease.
• Re-fit the pin (C) inside hub body with the spacer (Z) (Pic. 2).
• Take care to position of the pawls positions. Lock with power the
mobile side with a torque of 15 Nm (Pic. 3). If necessary adjust the
hub by working on the ring (D).
• Unlock the grub screw (E) with a key (B) (Pic. 3).
• Turn the ring clockwise to drop the sliding, and counterclockwise
to rise the sliding.
• Lock the grub screw (E).
• Check the sliding of the wheel.
Please check that the hub is correctly tightened and closed, fai-
lure to do so could lead to a serious or fatal accident.
Warning
!
Use original spare parts exclusively provided by Fac Michelin S.r.l.
Any modification or alteration (also graphic) of the product with
non-original spare parts or spare parts not delivered directly by
Fac Michelin S.r.l., involves the expiration of the guarantee.
spOKes
3
When replacing any broken spokes please ensure spokes of the
correct length and specification are used.
SYNTIUM
Right side
Left side
cHANge A spOKe
Warning
!
If you have any doubt whatsoever your service-repair ability,
please take your bicycle to a qualified repair shop.
Before any maintenance operations on your wheels, always
wear gloves and protection glasses.
Use only spokes and nipples of the same length and characteri-
stics of those being replaced.
Use original spare parts exclusively provided by Fac Michelin Srl.
frONT HuB
• Insert two keys (A) in the extremity of the hubs. Turn them
counterclockwise.
• Once you take out the mobile side, if it is necessary take out the
complete pin from the opposite side.
• Take out the damaged spoke, then put in the new spoke (Pic.4).
• If it is necessary put the pin into hub' s body, and lock with power
the mobile side with a torque of 15 Nm.
• If it is necessary, adjust the hub by working on the ring (D), as
explained on the Section 2 / Hubs / Rear hub.
• Check the sliding of the wheel.
Please check that the hub is correctly tightened and closed, fai-
lure to do so could lead to a serious or fatal accident.
reAr HuB
To change a spoke on the left side of the hub:
• Insert two keys (A) inside the extremity of the hub and turn them
in counterclockwise.
• Once you take out the mobile side, take out the damaged spoke,
Rear wheel Front wheel
281 mm 284 mm
282 mm 284 mm