Product Parts; Preparing For Installation; Installation In The Vehicle - CYBEX ANORIS T i-SIZE Manual Del Usuario

PRODUCT PARTS

Linear Side-impact Protection
(L.S.P.) (1)
Battery protection strip (2)
Battery compartment (3)
Load leg (4)
Display panel (5)
ISOFIX Release buttons (6)
ISOFIX Locking arms (7)
ISOFIX Anchorage points (8)
ISOFIX Indicators (9)
Load leg adjustment button (10)
Load leg indicator (11)
Headrest (12)

PREPARING FOR INSTALLATION

The Linear Side-impact Protection (L.S.P) (1) folds out automatically when taking
out the car seat from the packaging. Make sure that the Linear Side-impact
Protection (L.S.P) facing the vehicle door is fully folded out before starting your drive.
Before first use, the battery protection strip (2) must be removed from the battery
compartment (3) at the bottom of the car seat.
As soon as installation of the car seat is started, an acoustic warning signal can be
heard until the load leg (4) is correctly installed.
If installation is started and there sounds no audible warning signal or the visual
indicators on the display panel (5) are not lit, the batteries must be replaced.
THE CORRECT POSITION IN THE VEHICLE
This is an i-Size Enhanced Child Restraint System. It is approved according to UN
Regulation No. R129/03, for use in i-Size compatible vehicle seating positions as
indicated by vehicle manufacturers in their vehicle user manuals. If your vehicle
does not have an i-Size seating position, please check with the enclosed vehicle
type list whether the use is permitted.
You can obtain the most up-to-date version of the type list from
www.cybex-online.com.
If your vehicle is not equipped with ISOFIX, the car seat cannot be used.
If your vehicle does not offer enough space, the Linear Side-impact Protection
(L.S.P) can be folded in.
Headrest adjustment handle (13)
Position adjustment handle (14)
Impact shield (15)
Belt adjustment buttons (16)
Belt buckle (17)
Buckle tongue (18)
Adjustment belts (19)
Check button (20)
Impact shield indicator (21)
Battery indicator (22)
L.S.P. locking button (23)
User guide compartment (24)
It is not guaranteed that all sitting and reclining positions can be used in all
approved vehicles.
For safety and comfort reasons, we recommend using the vehicle seat behind
��
the front passenger.

INSTALLATION IN THE VEHICLE

Always ensure that...
• the backrests in the vehicle are locked in their upright position.
• when installing the car seat on the front passenger seat, adjust the vehicle
seat as far back as possible
1. Fold out the load leg (4) until it locks into its foremost position.
2. Place the car seat on an appropriate seat in the vehicle.
3. Release the ISOFIX Release buttons (6) to extend the ISOFIX Locking arms
(7).
The ISOFIX Release buttons can both be released independently allowing the
��
ISOFIX Locking arms to be adjusted independently.
4. Push the ISOFIX Locking arms (7) out of the car seat to their furthest extent.
5 Push the ISOFIX Locking arms (7) into the ISOFIX Anchorage points (8) until
these lock into place with an audible "CLICK". The ISOFIX Indicators (9) will
switch from RED to GREEN.
The ISOFIX Anchorage points are two metal lugs per vehicle seat. These are
��
located between the backrest and the seat surface of the vehicle seat. If in
doubt, refer to the user manual of your vehicle.
6. Make sure that the car seat is firmly attached to the ISOFIX Anchorage points
(8) by trying to remove it from it.
7. Push the car seat towards the backrest of the vehicle seat until it is fully
aligned with the backrest.
8. Press the load leg adjustment button (10) and extend the leg until it firmly
touches the vehicle floor.
9. The load leg indicator (11) switches to GREEN when the load leg is correctly
positioned on the vehicle floor and the acoustic warning signal will stop.
10. Pull the load leg (4) out to the next locking position to ensure optimal force
transmission.
Moving the car seat from side to side will also brace it against the vehicle
��
backrest.
EN
7