1
1
EN
2.3
Intended Use
EN
This product is part of the Cleco Production Tools tighten-
ing system. It is intended for use in industrial fastening
processes. Only use the tool under the following condi-
tions. The user is liable for damage caused by improper
use.
•
Only in conjunction with the components listed in the
EU Declaration of Conformity.
•
Under the prescribed ambient conditions.
Within the power range, which is specified in the tech-
•
nical data.
With equipment parameters set up properly.
•
In EMC Limit Class A (electromagnetic immunity for
•
industrial areas). For the currently observed EMC
standards, see the EU Declaration of Conformity.
With the recommended battery and charger.
•
2.4
Foreseeable misuse
► DO NOT use the tool as a hammer.
► DO NOT use a controller other than the one listed
inthe EC Declaration of Conformity.
► DO NOT use the tool in potentially explosive areas.
► DO NOT use the tool in damp spaces or outdoors.
► DO NOT disassemble or modify the tool.
2.5
Operator Training
The tightening system may only be put into operation, ad-
justed and maintained by personnel that have been
trained and qualified by employees of Apex Tool Group.
The tool has been preset by Apex Tool Group. Changes to
the default settings can only be made by a qualified em-
ployee
1
1). Additional information see Programming Man-
ual.
2.6
Standards
It is mandatory that national, state, and local codes and
standards be followed.
FCC- and IC Compliance
This product complies with Part 15 of the FCC Rules. Any
changes or modifications not expressly approved by the
manufacturer could void the user's authority to operate this
product. Operation is subject to the following two condi-
tions:
•
This product may not cause harmful interference.
•
This product must accept any interference received,
including interference that may cause undesired oper-
ation.
FCC Responsible party
Name: William Cain
Position: Director, R&D
Address: 670 Industrial Drive
Lexington, SC 29072
United States
Phone: +1 803 951 7558
1
Qualified employees have the training and experience to
identify potentially hazardous situations. They can initiate
12
Email: William.Cain@ClecoTools.com
This product has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide rea-
sonable protection against harmful interference when the
product is operated in a commercial environment. This
product generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to
radio communications.
Operation of this product in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.
2.7
General Power Tool Safety Warnings
Read all safety warnings, instructions, illustrations
and specifications provided with this power tool. Fail-
ure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future refer-
ence.
The term "power tool" in the warnings refers to mains-op-
erated (corded) power tool or battery-operated (cordless)
power tool.
1 Work area safety
a)
Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
Do not operate power tools in explosive atmos-
b)
pheres, such as in the presence of flammable liq-
uids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c)
Keep children and bystanders away while operat-
ing a power tool. Distractions can cause you to lose
control.
2 Electrical safety
a)
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will re-
duce risk of electric shock.
b)
Avoid body contact with earthed or grounded sur-
faces, such as pipes, radiators, ranges and refrig-
erators. There is an increased risk of electric shock if
your body is earthed or grounded.
Do not expose power tools to rain or wet condi-
c)
tions. Water entering a power tool will increase the
risk of electric shock.
Do not abuse the cord. Never use the cord for car-
d)
rying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk
of electric shock.
e)
When operating a power tool outdoors, use an ex-
tension cord suitable for outdoor use. Use of a
appropriate safety measures and are obliged to comply
with regulations.
P2547BA | 2021-08
Apex Tool Group