Hitachi Koki C 10FCG Instrucciones De Seguridad Y Manual De Instrucciones página 12

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

English
(1) Setting to cut crown moldings at positions 1 and 4 in Fig. 19 (see
Fig. 20; tilt the motor head to the left):
1 Turn the turntable to the right and set the Miter Angle as follows:
∗ For 45° type crown moldings:
∗ For 38° type crown moldings:
2 Tilt the motor head to the left and set the Bevel Angle as follows:
∗ For 45° type crown moldings:
∗ For 38° type crown moldings:
3 Position the crown molding so that the upper surface (Ⓐ in Fig. 18)
contacts the fence as indicated in Fig. 22.
(2) Setting to cut crown moldings at positions 2 and 3 in Fig. 19 (see
Fig. 21; tilt the head to the left):
1 Turn the turntable to the left and set the Miter Angle as follows:
∗ For 45° type crown moldings:
∗ For 38° type crown moldings:
2 Tilt the head to the left and set the Bevel Angle as follows:
∗ For 45° type crown moldings:
∗ For 38° type crown moldings:
3 Position the crown molding so that the lower surface (Ⓑ in Fig. 18)
contacts the fence as in Fig. 23.
1
Miter angle scale
Turntable
2
Fence
(Left side)
Fence
Fence
12
35.3° ( mark)
31.6° ( mark)
30° ( mark)
33.9° ( mark)
35.3° ( mark)
31.6° ( mark)
30° ( mark)
33.9° ( mark)
Head
Bevel angle scale
4
Fence
(Right side)
Base
Fig. 20
Head
Bevel angle scale
3
Base
Turntable
Miter angle scale
Fig. 21
Table on base
Fig. 22
Table on base
Fig. 23
Cutting method of crown molding without tilting the saw blade.
(1) Crown molding Stopper (L) and (R) (optional accessories) allow easier
cuts of crown molding without tilting the saw blade. Install them in the
base both-sides side to be shown in Fig. 24-a. After inserting Tighten the
6mm knob bolts to secure the crown molding Stoppers.
[Optional accessories used]
• Crown molding Vise Ass'y (Include Crown molding Stopper (L))
• Crown molding Stopper (L)
• Crown molding Stopper (R)
Crown molding
vise ass'y
6mm Wing
(Optional
bolt
accessories)
6mm Wing
bolt
Crown molding stopper (L)
(Optional accessories)
6mm Wing bolt
Fig. 24-a
(2) The crown molding vise (B) (Optional accessory) can be mounted on
either left side of the fence or the right side of the fence. It can unite with
the slope of the crown molding and vice can be pressed down.
Then turn the upper knob, as necessary, to securely attach the crown
molding in position. To raise or lower the vise assembly, fi rst loosen the
6mm knob bolt.
After adjusting the height, fi rmly tighten the 6mm wing bolt; then turn
the upper knob, as necessary, to securely attach the crown molding in
position. (See Fig. 24-b)
Crown molding vise ass'y
(Optional accessories)
6mm Knob
bolt
Fence
Crown
6mm Wing bolt
molding
Fig. 24-b
WARNING:
Always fi rmly clamp or vise to secure the crown molding to the
fence; otherwise the crown molding might be thrust from the table
and cause bodily harm.
Do not bevel cutting. The main body or saw blade may contact the
sub fence, resulting in an injury.
CAUTION:
Always confi rm that the motor head (see Fig. 1) does not contact
the crown molding vise ass'y when it is lowered for cutting. If
there is any danger that it may do so, loosen the 6mm knob bolt
and move the crown molding vise ass'y to a position where it will
not contact the saw blade.
Position crown molding with its WALL CONTACT EDGE against the guide
fence and its CEILING CONTACT EDGE against the crown molding
Stoppers as shown in Fig. 24-b.
Adjust the crown molding Stoppers according to the size of the crown
molding.
Tighten the 6mm wing bolt to secure the crown molding Stoppers.
Crown molding stopper (R)
(Optional accessories)
Knob
Crown molding stopper (L)
Crown molding stopper (R)
(Optional accessories)

Publicidad

Tabla de contenido
loading

Tabla de contenido