Sime MURELLE HE 110 R Manual De Usuario página 85

3.3 ACCESS TO
INSTALLER'S
PARAMETERS
For access to the installer's parameters,
press simultaneously the keys
or 2 seconds (3 fig. 12).
For example, the parameter PAR 23 is
visualised on the display of the control
panel in the following way:
The paramet er s scr oll for war ds and
backwards with the key and
the default parameters can be changed
with the keys and .
The standard visualisation returns automa-
tically after 60 seconds, or by pressing one
of the control keys (2 fig. 12) excluded the
key RESET.
3.3. 1 Replacing the board or
RESETTING parameters
If the electronic board is replaced or reset,
it is necessary to configure PAR 1 and PAR
2 by associating the following values to
each type of boiler to be able to restart the
boiler:
GAS MODEL
Single (110 R)
METHANE
(G 20)
Sequence/cascade
Single (110 R)
PROPANE
(G 31)
Sequence/cascade
FAST CONFIGURATION
PAR DESCRIPTION
1 Combustion configuration
and
2 Hydraulic configuration
3 Timetable 2 programmer
4 Pressure transducer disabler
5 Assignment of auxiliary relay AUX
and
6 Luminous bar indicating presence
of voltage
7 Allocation of CR73 channels
8 Fan rpm Step ignition
9 Long chimneys
10 Remote control option setting
11 Correction values external sensor
12 Backlighting duration
13 Modulating pump speed
PAR 1
14 Setting second input TA
7
15 Cascade address
8
16 ModBus address
17 ModBus communication configuration
19 Type circuit
15
D.H.W. - HEATING
PAR DESCRIPTION
16
20 Minimum heating temperature Zone 1
21 Maximum heating temperature Zone 1
22 Heating curve slope Zone 1
23 Minimum heating temperature Zone 2
24 Maximum heating temperature Zone 2
25 Heating curve slope Zone 2
26 Minimum heating temperature Zone 3
27 Maximum heating temperature Zone 3
28 Heating curve slope Zone 3
∆t heating circuit
29
30 Post-circulation heating time
31 Maximum heating capacity
32 Zone 1 pump activation delay
33 Start-up delay
34 Additional source activation threshold
35 Boiler antifreeze
36 External sensor antifreeze
37 Band saturation
flowmeter modulation
38 D.H.W. post-circulation time
39 Anti-legionella
(only D.H.W tank))
PARAMETERS INSTALLER
RANGE UNIT OF
MEASUREMENT
-- = ND
1 ... 22
-- = ND
1 ... 9
1 = DHW + Recirc. pump
2 = DHW
3 = Recirculation pump
0 = Disabled
1 = Enabled 0-4 BAR
2 = Enabled 0-6 BAR
3 = Enabled 0-4 BAR (NO ALL 09)
4 = Enabled 0-6 BAR (NO ALL 09)
1 = Remote supply
2 = Recirculation pump
3 = Automatic load.
4 = Remote alarm NC
5 = Heat pump
6 = Zone 2 valve
0 = Disabled
1 = Enabled
0 = Not assigned
1 = Circuit 1
2 = Three-zone circuit
0,0 ... 81 rpmx100 0, 1 from 0, 1 to 19,9
0 ... 20
1 = CR 73
2 = CR 53
3 = RVS 43. 1 43
4 = RVS 46.530
5 = RVS 61.843
-5 ... +5
-- = Always sec. x 10
0 = Never
1 ... 199
-- = None
AU = Automatic mod.
30... 1 00 = % Settable
modulation
-- = Contact TA
5... 1 60 = Input 0... 1 0VDC
-- = Not enabled
0 = Master
1...7 = Slaves
-- = Not enabled
1...31 = Slaves
1 ... 30
0 = Two zones
1 = Three zones
RANGE UNIT OF
MEASUREMENT
PAR 64 OEM ... PAR 21
PAR 20 ... PAR 65 OEM
3 ... 40
PAR 64 OEM ... PAR 24
PAR 23 ... PAR 65 OEM
3 ... 40
PAR 64 OEM ... PAR 27
PAR 26 ... PAR 65 OEM
3 ... 40
10 ... 40
0 ... 199
30 ... 100
0 ... 199
0 ... 10
-- , -10 ... 40
0 ... +20
-5 ... +5
-- = Disabled
0 ... 100
0 ... 199
0 = Disabled
1 = Enabled
INC/DEC DEFAULT
UNIT SETTING
= = "- -"
= = "- -"
= = 1
= = 1
= = 1
= = 1
= = 1
0,0
1 from 20 to 81
% 1 0
= = 1
°C 1 0
1 3
% 10 --
-- -- --
-- 1 --
-- 1 --
-- 1 25
-- -- 0
INC/DEC DEFAULT
UNIT SETTING
°C 1 20
°C 1 80
-- 1 20
°C 1 20
°C 1 80
-- 1 20
°C 1 20
°C 1 80
-- 1 20
°C 1 20
Sec. 10 30
% 1 100
10 sec. 1 1
Min. 1 3
°C 1 "- -"
°C 1 3
°C 1 -2
% 1 100
Sec. 1 0
-- -- 0
ES
PT
ENG
85