Dremel 8100 Instrucciones De Funcionamiento Y Seguridad página 13

1600A012FW_8100 1/30/17 12:27 PM Page 13
FIxING STUCK COLLETS – It is possible for a
collet to get stuck within the collet nut especially if
a collet nut is tightened onto the tool without a bit
in place. If this happens, the collet can be
removed from the collet nut by pushing the shank
of an accessory into the hole in the collet nut.
This should cause the collet to pop out of the
collet nut.
BALANCING ACCESSORIES — For
precision work, it is important that all
Dremel 8100
Thank you for purchasing the Dremel 8100.
This product was designed by the many
Dremel users who passionately use their
rotary tools daily. This tool was designed to
give you the ultimate performance when
working on projects.
The Dremel 8100 is one of the MOST
versatile cordless rotary tool available today. It
has a wide speed range including a high
performance motor that allows the tool to
maintain its speed under load. The design of
the tool also contains plenty of soft grip so the
tool can be held comfortably in many
positions. The quick collet lock mechanism
makes locking the output shaft easier for
changing accessories. You will appreciate the
many applications that the Dremel 8100 can
easily tackle.
Rotary Tool Introduction
The Rotary Tool has a small, powerful electric
motor, is comfort able in the hand, and is made
to accept a large variety of accessories
including abrasive wheels, drill bits, wire
brushes, polishers, engraving cutters, router
bits, cutting wheels and attachments.
Accessories come in a variety of shapes and
permit you to do a number of different jobs. As
you be come familiar with the range of
accessories and their uses, you will learn just
how versatile the Rotary Tool is. You'll see
dozens of uses you hadn't thought of before.
The real secret of the Rotary Tool is its speed.
To understand the advantages of its high
speed, you have to know that the standard
portable electric drill runs at speeds up to 2,800
revolutions per minute. The Rotary Tool
accessories be in good balance (much the
same as the tires on your automobile). To true
up or balance an accessory, slightly loosen
collet nut and give the accessory or collet a 1/4
turn. Re tighten collet nut and run the Rotary
Tool. You should be able to tell by the sound
and feel if your accessory is running in
balance. Continue adjusting in this fashion until
best balance is achieved. To maintain balance
on abrasive wheel points, before each use,
with the wheel point secured in the collet, turn
on the Rotary Tool and run the 415 Dressing
Stone lightly against the revolving wheel point.
This removes high spots and trues up the
wheel point for good balance.
Operating Instructions
operates at speeds up to 30,000 revolutions
per minute. The typical electric drill is a low-
speed, high torque tool; the Rotary Tool is just
the opposite – a high-speed, low torque tool.
The major difference to the user is that in the
high speed tools, the speed combined with the
acces sory mounted in the collet does the work.
You don't apply pressure to the tool, but simply
hold and guide it. In the low speed tools, you
not only guide the tool, but also apply pressure
to it, as you do, for example, when drilling a hole.
It is this high speed, along with its compact size
and wide variety of special accessories and
attachments, that makes the Rotary Tool differ -
ent from other tools. The speed enables it to do
jobs low speed tools cannot do, such as cutting
hardened steel, en graving glass, etc.
Getting the most out of your Rotary Tool is a
matter of learning how to let this speed work
for you. To learn about more uses and the
versatility of Dremel accessories and
attachments refer to this Owner's Manual or
check our website at www.Dremel.com.
The first step in learning to use the Rotary
Tool is to get the "feel" of it. Hold it in your
hand and feel its weight and balance. Feel the
taper of the housing.
WARNING
Wear Eye Protection
13
Using the Rotary Tool
Always hold the tool
away from your face.
Accessories can be
damaged
handling, and can fly
apart as they come up
to speed. This is not
common, but it does
happen.
during