Emission Levels; Technical Data; Machine Features - Festool TXS Manual De Instrucciones Original

Taladro atornillador de batería
Ocultar thumbs Ver también para TXS:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 22
– Protect the battery pack from excessive heat > 50
°C or constant heat sources such as sunlight or
naked flames!
– Never use water to extinguish burning li-ion bat-
tery packs! Use sand or a fire blanket.
– Check the plug and the cable regularly and
should either become damaged, in order to avoid
a hazard, have them replaced by an authorised
after-sales service workshop.
– Always pull the mains plug out of the socket
when the charger is not in use.
2.4

Emission levels

Levels determined in accordance with EN 60745 are
typically:
Sound pressure level
Sound power level
Uncertainty
Wear ear protection.
Vibration emission value a
directions) and uncertainty K measured in accor-
dance with EN 60745:
Fastening
Drilling in metal
The specified emission values (vibration, noise)
– are used to compare machines.
– They are also used for making preliminary esti-
mates regarding vibration and noise loads during
operation.
– They represent the primary applications of the
power tool.
Increase possible for other applications, with other
insertion tools or if not maintained adequately. Take
note of idling and downtimes of machine!
3
Intended use
Cordless drill suitable
– for screwing in and tightening screws,
– for drilling in metal, wood, plastics and similar
materials.
Not intended for clamping tools other than drills
and drill bits, e.g. compass saws, stirring rods,
metal brushes.
Charger MXC suitable
– for charging the listed battery packs.
– only for indoor use.
L
= 65 dB(A)
PA
L
= 76 dB(A)
WA
K = 3 dB
(vector sum for three
h
a
=4,0 m/s
h
K = 1,5 m/s
a
=3,0 m/s
h
K = 1,5 m/s
The user is liable for improper or non-in-
tended use; this also includes continuous in-
dustrial operation.
4

Technical data

Cordless drills
Motor voltage
Idle engine speed*
Max. torque
soft/hard screw joints
Adjustable torque
Chuck clamping range
Drill diameter max.
Wood/Metal
Tool holder in drill spindle
Weight without battery pack with
Centrotec
* Speed specifications with fully charged battery
pack.
Further technical data on the charger and the
2
supplied battery pack can be found on page 6.
2
5

Machine features

2
2
[1-1]
Drilling symbol
[1-2]
Torque thumbwheel
[1-3]
Torque/drilling position marking
[1-4]
Gear switch
[1-5]
Right/left switch
[1-6]
On/Off switch
[1-7]
Belt clip
[1-8]
Insulated gripping surfaces (grey shaded
area)
[1-9]
Button for releasing the battery pack
[1-10] LED lamp with capacity indicator
[1-11] Bit store
[3A]
Wall mount for charger
The specified illustrations appear at the beginning
of the Operating Instructions.
6
Operation
6.1
Changing the battery pack [2]
Battery pack is ready for use immediately upon
delivery and can be charged at any time.
TXS
GB
TXS
10,8V
1st gear
0 - 430 rpm
2nd gear 0 - 1300 rpm
10/ 16 Nm
0,3 - 3,4 Nm
1 - 10 mm
12/ 8 mm
1/4 ''
0,7 kg
13

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Txs li 2,610008076

Tabla de contenido