Campbell Hausfeld CS Serie Instrucciones De Operación página 3

Important Safety Information (Continued)
GENERAL SAFETY
◆
Read all manuals included with this product
carefully. Be thoroughly familiar with the controls
and the proper use of the equipment.
◆
Follow all local electrical and safety codes as well as
the United States National Electrical Codes (NEC) and
Occupational Safety and Health Act (OSHA).
◆
Only persons well acquainted with these rules of safe
operation should be allowed to use the compressor.
◆
Keep visitors away and NEVER allow children in the work
area.
◆
Wear safety glasses and use hearing protection when
operating the unit.
◆
Do not stand on or use the unit as a handhold.
◆
The protection devices fitted to this compressor are provided
to offer safety of operation. The operator is solely responsible
for personal safety at all times.
These devices should not be adjusted except by an
authorised service agent.
◆
Before each use, inspect compressed air system and
electrical components for signs of damage, deterioration,
weakness or leakage. Repair or replace defective items
before using.
◆
Check all fasteners at frequent intervals for proper tightness.
Motors, electrical equipment
and controls can cause
electrical arcs that will ignite a fl ammable gas or
vapor. Never operate or repair in or near a fl ammable
gas or vapor. Never store fl ammable liquids or gases
in the vicinity of the compressor.
Never operate compressor
without a beltguard. This unit
can start automatically without warning. Personal
injury or property damage could occur from contact
with moving parts.
◆
Do not wear loose clothing or jewelry that will get caught in
the moving parts of the unit.
Compressor parts may be hot
even if the unit is stopped.
◆
Keep fingers away from a running compressor;
fast moving and hot parts will cause injury and/or
burns.
◆
If the equipment should start to vibrate abnormally, STOP
the engine/motor and check immediately for the cause.
Vibration is generally an indication of trouble.
◆
To reduce fire hazard, keep engine/motor exterior free of oil,
solvent, or excessive grease.
An ASME code safety relief valve with
a setting no higher than the Maximum
Allowable Working Pressure (MAWP) of the tank MUST be
SERIES CS ROTARY SCREW COMPRESSORS
installed in the air lines or in the tank for this compressor.
The ASME safety valve must have suffi cient fl ow and pressure
ratings to protect the pressurized components from bursting.
MANUAL
The fl ow rating can be found in the parts manual. The safety
valve in the intercooler does not provide system protection.
valves set higher than the factory setting.
◆
Never attempt to adjust ASME safety valve. Keep safety
valve free from paint and other accumulations.
drilling or any other modifi cation will weaken the
tank resulting in damage from rupture or explosion.
Always replace worn, cracked or damaged tanks.
◆
Tanks rust from moisture build-up, which weakens the tank.
Make sure to drain tank regularly and inspect periodically for
unsafe conditions such as rust formation and corrosion.
◆
Fast moving air will stir up dust and debris which may
be harmful. Release air slowly when draining moisture or
depressurizing the compressor system.
SPRAYING PRECAUTIONS
fl ame or near ignition sources including the
compressor unit.
◆
Do not smoke when spraying paint, insecticides,
or other flammable substances.
◆
Use a face mask/respirator when spraying and
spray in a well ventilated area to prevent health
and fire hazards.
◆
Do not direct paint or other sprayed material
at the compressor. Locate compressor as far away from
the spraying area as possible to minimize overspray
accumulation on the compressor.
◆
When spraying or cleaning with solvents or toxic
chemicals, follow the instructions provided by the chemical
manufacturer.
The DANGER, WARNING, CAUTION, and NOTICE
notifications and instructions in this manual cannot cover all
possible conditions and situations that may occur. It must
be understood by the operator that caution is a factor which
cannot be built into this product, but must be supplied by
the operator.
Maximum operating pressure is 150 psi. Do
not operate with pressure switch or pilot
Never attempt to repair
or modify a tank! Welding,
Drain liquid from tank daily.
Do not spray fl ammable
materials in vicinity of open
SAVE THESE INSTRUCTIONS
DO NOT DISCARD
www.campbellhausfeld.com
3