Specifications - Jacuzzi ALLUSION 6636 Manual De Instalación Y Operación

Important: Read complete instructions before beginning installation.
Each bath arrives ready for installation, completely equipped with blower motor, pump/motor assembly, heater, and plumb-
ing necessary for operation.
Remove the bath from the carton. Retain the shipping carton until satisfactory inspection of the product has been made. Do
not lift the bath by the plumbing or wiring at any time; handle by the shell only.
Immediately upon receipt, inspect the shell before installing. Should inspection reveal any damage or defect in the finish, do
not install the bath. Damage or defect to the finish claimed after the bath is installed is excluded from the warranty. Jacuzzi
Whirlpool Bath's responsibility for shipping damage ceases upon delivery of the products in good order to the carrier. Refer any
claims for damage to the carrier. For definitions of warranty coverage and limitations, refer to the published warranty informa-
tion packed with the product.
All bath units are factory tested for proper operation and watertight connections prior to shipping. Note: Prior to installa-
tion, the bath must be filled with water and operated to check for leaks that may have resulted from shipping damage
or mishandling. Jacuzzi Whirlpool Bath is not responsible for any defect that could have been discovered, repaired, or
avoided by following this inspection and testing procedure.
RECTANGULAR BATHS
4"
L
2"
(Blower)
SIDE VIEW

SPECIFICATIONS

(Rectangular)
DIMENSIONS
MODEL
66" (1676 mm) L
ALLUSION 6636
36" ( 914 mm) W
26" ( 660 mm) H
ALLUSION 7236 72" (1829 mm) L
36" ( 914 mm) W
26" ( 660 mm) H
ALLUSION 7242
72" (1829 mm) L
42" (1067 mm) W
26" ( 660 mm) H
NOTE: The overall dimensions are nominal with a tolerance of +0 and -1/4".
FOR ALL UNITS: Electrical Service Requirements: All require a dedicated GFCI protected separate circuit.
Blower: 120VAC, 20AMP, 60 Hz. dedicated GFCI protected separate circuit.
Motor/Pump and RapidHeat: 240VAC, 20AMP, 60 Hz. dedicated GFCI protected separate circuit.
SPECIFICATIONS
(Heater) H
(Motor)
END VIEW
ALLUSION SIDE END
DRAIN/OVERFLOW CUTOUT FLOOR LOADING
17-3/8" (441 mm) A
Template
11-15/16" (210 mm) B
Provided
P/N
BY20000
17-3/8" (441 mm) A
Template
11-15/16" (210 mm) B
Provided
P/N
BY20000
17-3/8" (441 mm) A
Template
11-15/16" (210 mm) B
Provided
P/N
BY20000
W
TOTAL WEIGHT/ PRODUCT
OPERATING
WEIGHT
GALLONAGE
856 lb
55 U.S. gal 200 lb
(389 kg)/
(208 liters) (59 kg)
52 lb/sq. ft.
(253 kg/sq. m)
70 U.S. gal
1001 lb
220 lb
(265 liters)
(455 kg)/
(66 kg)
56 lb/sq. ft.
(272 kg/sq. m)
1246 lb
85 U.S. gal 240 lb
(566 kg)/
(322 liters) (73 kg)
59 lb/sq. ft.
(289 kg/sq. m)
1
Jacuzzi Whirlpool Bath© BR28000A
A
B
DRAIN/OVERFLOW
HEATER READY
FOR FIELD
SKIRT &
INSTALLATION
MOUNTING
Factory Installed
Not Available
(BN60000 HEATER 230V)
Not Available
Factory Installed
(BN60000 HEATER 230V)
Factory Installed
Not Available
(BN60000 HEATER 230V)
3/05