Maintenance Instructions - Jacuzzi ALLUSION 6636 Manual De Instalación Y Operación

Cleaning the Bath
To clean your bath, simply use a mild, nonabrasive liquid
detergent solution. You can protect and restore the gloss to
a dulled acrylic surface by applying Meguiar's #10 Mirror
Glaze, a product specifically designed for use on acrylic fin-
ishes. If Meguiar's is not available, an acrylic polish of equal
quality or automotive paste wax is acceptable.
Never use abrasive household cleaners on any Jacuzzi
Whirlpool Bath product.
Repairs to the Surface
Minor scratches which do not penetrate the color finish
can be removed by lightly sanding with 600-grit wet/dry sand-
paper. Restore the gloss using Meguiar's Mirror Glaze or
automotive paste wax.
Major scratches and gouges which penetrate the acrylic
surface will require refinishing. To obtain a referral for a ser-
vice agent in your area call 800-288-4002 or visit our web
site at http://www.jacuzzi.com/, then navigate and select Fin-
ish, Surface or Shell-Related Problems for a listing of autho-
rized agents, contractors, or distributors.
Purging the Whirlpool System
NOTE: THE WHIRLPOOL SYSTEM SHOULD BE PURGED
AT LEAST TWICE A MONTH
To remove accumulations of bath residue from the whirlpool
system, it is recommended that a whirlpool bath be purged at
least twice a month. For best results, however, we recom-
mend that you purge your whirlpool bath after each use using
our exclusive two-part plumbing system cleaner made specifi-
cally for whirlpool baths. Systems Clean™ is available
through an authorized Jacuzzi Whirlpool Bath Distributor or by
calling us direct at 1-800-288-4002. Instructions for use:
Immediately after bathing and exiting the whirlpool bath,
leave the bath water in the tub and add hot water, if necessary,
so the water is at least 2" above the highest jet. Turn ON the
unit without the aerator. Pour the contents of the Systems
Clean Packet 1 (taking care not to get the material on yourself)
into the bath near the intake for the circulation pump. Repeat
same process with Systems Clean Packet 2. It is important
to use Packet 1 before Packet 2 to avoid a strong odor.
Run the bath for 5 to 10 minutes. Drain completely and rinse
any residue.
If you have followed the standard purging instructions above
and still have an excess accumulation of bath residue and
desire an alternative cleaning mechanism, we recommend
SUPER SYSTEMS CLEAN™ PLUS manufactured by Stearns
Packaging to rectify this condition. This may be obtained by
contacting us at l-800-288-4002. It is recommended that you
follow the instructions provided by the manufacturer with the
product. Repeated use may be necessary. SUPER SYS-
TEMS CLEAN™ PLUS does not replace the necessity to
regularly purge your whirlpool system with Systems Clean as
recommended.
(For additional information about water content, contact us at
l-800-288-4002 for a copy of the Jacuzzi Water Quality
Primer.)
Jacuzzi Whirlpool Bath© BR28000A 3/05

MAINTENANCE INSTRUCTIONS

Bath Additives
NOTE: DO NOT USE OIL OR OIL BASED BATH ADDI-
TIVES.
If you want to use any kind of bath additive, use only a small
amount of low-foaming powder or crystal substance; the
whirlpool action intensifies the foaming properties of soaps.
The use of certain bath oils, bubble baths, and bath additives
may increase the level of accumulations of bath residue in the
whirlpool system. If excess accumulations persist, you should
discontinue use of these products.
Purging the Air Bath
has shut off (either with the ON/OFF button or at the end of a
20 minute cycle), the blower will come on for a 1 minute purge
cycle to blow water out of the piping of the system. The LED
flashes during the 60 minute pause. NOTE: When the bubble
function is used and turned OFF, the blower will remain on
for 15 seconds to cool down the heating element.
blower ON then OFF. The blower will come on in 60 minutes
for one minute.
the same time every day. To activate, hold the up arrow
button for 5 seconds when the blower/heater is OFF or wait-
ing for the normal purge. The LED will flash twice. If the unit
is in standby for the normal purge when activating the 24
hour cycle, the normal purge will be cancelled. When the 24
hour purge is activated, the LED will continuously flash (at a
slower rate than during normal purge). The purge will then
come on at the same time every day. To cancel the 24 hour
cycle, press the up arrow button (LED will stop flashing).
NOTE: The unit contains a drain down solenoid mechanism.
When the drain is closed, the solenoid is also closed. When
the drain is open the solenoid is open to allow draining of the
bottom air channels. When the bath is not in use, the drain
should be left open otherwise the solenoid will continually be
on.
12
If the bubble function is used, 60 minutes after the control
If the bath is used without the bubble function, turn the
A 24 hour purge cycle can be programmed to come on at