Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Mounting/Replacing a Sanding Sheet on the Sanding
Plate
The sanding plate 10 is fitted with Velcro backing for quick
and easy fastening of sanding sheets with Velcro adhesion.
Before attaching the sanding sheet 11, free the Velcro
backing of the sanding plate 10 from any debris by tapping
against it in order to enable optimum adhesion.
Selecting the Sanding Sheet
Depending on the material to be worked and the required rate of material removal, different sanding sheets are available:
Sanding disc
Red quality
Dust/Chip Extraction
l
Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful
to one's health. Touching or breathing-in the dusts can
cause allergic reactions and/or lead to respiratory
infections of the user or bystanders.
Certain dusts, such as oak or beech dust, are
considered as carcinogenic, especially in connection
with wood-treatment additives (chromate, wood
preservative). Materials containing asbestos may only
be worked by specialists.
– As far as possible, use a dust extraction system
suitable for the material.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filterclass respirator.
Observe the relevant regulations in your country for the
materials to be worked.
Connecting the Dust Extraction (see figure A)
For sanding, always connect dust extraction.
Remove the application tool/accessory when mounting the
dust extraction 15 (accessory).
If required, assemble the parts of the dust extraction 15 as
shown in the figure. Position the assembled dust extraction
onto the machine via the tool holder 4. Fasten the dust
extraction to the machine with the retaining clip 13 as
shown in the figure.
Depending on machine version, place a vacuum hose
(accessory) either directly onto the vacuum connection 14.
Connect the vacuum hose with a vacuum cleaner
(accessory). An overview for the connection of various
vacuum cleaners can be found on the fold-out page.
The vacuum cleaner must be suitable for the material being
worked.
Material
- All wooden
materials (e.g.,
hardwood, softwood,
chipboard, building
board)
- Metal materials
ENGLISH
13
Position the sanding sheet 11 flush alongside one edge of
the sanding plate 10, then lay the sanding sheet onto the
sanding plate and press firmly.
To ensure optimum dust extraction, pay attention that the
punched holes in the sanding sheet match with the holes in
the sanding plate.
To remove the sanding sheet 11, grasp it at one of the tips
and pull it off from the sanding plate 10.
Application
For coarse-sanding, e.g. of rough,
unplaned beams and boards
For face sanding and planing small
irregularities
For finish and fine sanding of wood
When vacuuming dry dust that is especially detrimental to
health or carcinogenic, use a special vacuum cleaner.
4. Operation
l
Observe correct mains voltage! The voltage of the
power source must agree with the voltage specified
on the nameplate of the machine. Power tools
marked with 230 V can also be operated with 220 V.
Starting Operation
Switching On and Off
To start the machine, push the On/Off switch 1 forward so
that the "I" is indicated on the switch.
To switch off the machine, push the On/Off switch 1 toward
the rear so that the "0" is indicated on the switch.
Preselecting the Orbital Stroke Rate
With the thumbwheel for preselection of the orbital stroke
rate 2, you can preselect the required orbital stroke rate,
even during operation.
The required stroke rate depends on the material and the
working conditions and can be determined through
practical testing.
Working Advice
Note: Do not cover off the venting slots 3 of the machine
while working, as this reduces the working life of the
machine.
13
Grain size
coarse
60
medium
80
fine
210
Publicidad
Tabla de contenido
