Publicidad
Idiomas disponibles
Idiomas disponibles
GB
IMPORTANT: If you suspect or discover asbestos is present in any area you are working in, seek
professional advice immediately. Removal of asbestos should be done by a licensed contractor.
Contact the HSE in the UK (www.hse.gov.uk) or your national health and safety authority in your
country for further information about dealing with asbestos. European Directive 2009/148/EC
provides additional information related to exposure to asbestos at work.
a) DO NOT allow anyone under the age of 18 years to use this tool. Ensure that operators are
qualified and familiar with the operating and safety instructions.
b) Use personal protective equipment (PPE) including safety glasses and protective
clothing.
c)
Wear respiratory protection suitable for the work being undertaken. A minimum rating of
FFP2 is recommended.
d) If operating the tool causes discomfort in any way, stop immediately and review your
method of use.
e) Wear suitable protective anti-vibration gloves that are non-fabric or coated fabric
to prevent loose strands of material catching in the rotating drill bit. Discard gloves
immediately if material is visibly frayed.
f)
Hammer drills produce a very high level of vibration when operating in hammer mode.
Frequent breaks are advised.
g) Use metal and voltage detectors to locate concealed electric, water or gas lines. Avoid
touching live components or conductors.
h) Ensure that the drill bit is securely fixed in the chuck. Insecure drill bits can be ejected from
the machine causing a hazard.
i)
Ensure that the lighting is adequate.
j)
Ensure that the drill bit is in contact with the workpiece prior to starting up the tool.
k) Before drilling, check that there is sufficient clearance for the drill bit under the
workpiece.
l)
Use both hands when operating this tool.
m) DO NOT put pressure on the tool; to do so would shorten its service life.
n) Drill bits get hot during operation; allow to cool prior to handling them.
o) NEVER use your hands to remove sawdust, chips or waste close by the bit.
p) If you are interrupted when operating the drill, complete the process and switch off
before looking up.
q) Where possible, use clamps or a vice to hold your work.
r)
ALWAYS disconnect the hammer drill from the electric supply before changing a drill bit.
s)
Examine the chuck regularly for signs of wear or damage. Have damaged parts repaired by
a qualified service centre.
t)
ALWAYS wait until the drill has come to a complete stop before putting it down.
u) On completion of the work, disconnect the tool from the power source and remove bit
from the machine.
v) Periodically check all nuts, bolts and other fixings and tighten where necessary.
w) Even when this tool is used as prescribed it is not possible to eliminate all residual risk
factors. If you are in any doubt as to the safe use of this tool, do not use it.
Battery & Charger Safety
Use the Battery Charger correctly
• Refer to the section of this manual relating to use of the Battery Charger (16) before attempting
to charge the Battery (12)
• Do not attempt to use the charger with any batteries other than those supplied. Keep your battery
charger clean; foreign objects or dirt may cause a short or block air vents. Failure to follow these
instructions may cause overheating or fire
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard
• Examine the battery charger regularly for damage, especially the cord, plug and enclosure. If the
battery charger is damaged, it must not be used until it has been repaired
• Children should be supervised to ensure that they do not play with the appliance
WARNING: Do not attempt to recharge non-rechargeable batteries.
6
Battery Safety
WARNING: Li-ion batteries, if incorrectly used, stored or charged are a fire, burn and explosion
hazard.
• Keep the battery out of reach of children
• Only charge Li-ion batteries designed specifically for this charger
• Only use Li-ion batteries provided with this product or specifically designed to be compatible
• Allow batteries to cool for 15 minutes after charging or heavy use. Failure to follow these
instructions may cause overheating or fire
• When not in use batteries should be stored at room temperature (approximately 20˚C)
• Ensure battery contacts cannot accidentally short in storage. Keep batteries clean; foreign objects
or dirt may cause a short. Keep away from other metal objects, for example paperclips, coins,
keys, nails and screws
• Under abusive conditions, liquid may be ejected from the battery. This liquid may cause skin
irritation or burns. Avoid contact. If contact accidentally occurs, flush with water. If liquid contacts
eyes, seek medical help
• Do not open, disassemble, crush, heat above 60°C or incinerate. Do not dispose of in fire or
similar
• Do not get batteries wet or immerse in water
Battery & charger safety features
The Battery and Charger are fitted with a number of safety features which may be triggered during
charging or operation:
• Over-charge protection: Charger automatically switches off when the Battery has reached full
charge capacity, protecting the internal components of the battery
• Over-discharge protection: Prevents the Battery from discharging beyond the recommended
lowest safety voltage
• Over-heat protection: Sensor switches off if the Battery becomes too hot during operation.
This can happen if the tool is overloaded or being used for extended periods of time. Up to 30
minutes cooling time may be required depending on the ambient temperature
• Overload protection: Battery temporarily stops if it is overloaded or the maximum current draw is
exceeded, protecting the internal components. The Battery will resume normal operation when
the current draw returns to a normal safe level. This may take a few seconds
• Short circuit protection: The Battery will stop working immediately if a short circuit occurs, this
prevents damage to the Battery or tool
Product Familiarisation
1.
Chuck Jaws
2.
Chuck Collar
3.
Torque Selector
4.
Mode Selector
5.
Gear Selector
6.
Motor Vents
7.
On-Tool Battery Charge Indicator
8.
Forward/Reverse Switch
9.
Main Handle
10. Battery Mount
11. Battery Charge Indicator
12. Battery
13. Battery Release
14. Led Work Light
15. ON/OFF Trigger Switch
16. Battery Charger
17. Charger Terminals
18. Green LED
19. Red LED
Publicidad
