Silverline 998003 Manual De Instrucciones página 7

Intended Use
Battery-operated combi hammer drill with screwdriver, drill and impact drill functions suitable for
medium duty drilling and driving tasks. Includes hammer/impact function for light masonry drilling.
The tool must ONLY be used for its intended purpose. Any use other than those mentioned in this
manual will be considered a case of misuse. The operator, and not the manufacturer, shall be liable
for any damage or injury resulting from such cases of misuse. The manufacturer shall not be liable
for any modifications made to the tool, nor for any damage resulting from such modifications.
Unpacking Your Tool
• Carefully unpack and inspect your product. Fully familiarise yourself with all its features and
functions
• Ensure all parts of the product are present and in good condition
• If any parts are missing or damaged, have such parts replaced before attempting to use this
product
Before Use
Removing the Battery
• To remove the Battery (12), press the Battery Release (13) and slide the Battery out of the Battery
Mount (10) (Fig. I (a-b))
Installing a charged Battery
1. To fit a charged Battery (12), slide it onto the Battery Mount (10) (Fig. I (c))
Note: The Battery will fit only in one direction, which is determined by its shape and the design
of the Battery Mount. However, if the Battery does not slide into the Battery Mount easily, do not
force it. Instead, pull the Battery out of the Battery Mount again, check for correct position, and try
again gently.
2. Push the Battery into the Battery Mount until it locks into place securely
Setting up the Charger
1. If fitted, remove the Battery (12) from the Battery Mount (10) (Fig. II (b))
2. Connect the Battery Charger (16) to the mains power supply
3. The Green LED (18) on the Battery Charger will illuminate to indicate that the Charger is powered.
WARNING: Only use this Charger to charge the supplied Battery or identical Silverline
batteries.
WARNING: The Battery Charger is designed for indoor use only and must not be exposed to
moisture and rain.
Charging the Battery
WARNING: Failure to follow the correct procedure when charging the Battery (12) will result
in permanent damage.
Note: Normal charging time is 1 hour for a recently fully-discharged battery, but if the Battery has
been left in a discharged state for some time, it may take extended time to charge.
1. Slide a discharged or partially discharged Battery into the Battery Charger (16) (Fig. II (a))
Note: Make sure the Battery (12) and Battery Charger are lined up correctly. If the Battery does not
slide onto the Battery Charger easily, don't force it. Instead, remove the Battery, then check that
the top of the Battery and the Battery Charger slot are clean and undamaged and that the Charger
Terminals (17) are not bent.
2. Once charging commences, only the Red LED (19) will illuminate
Note: If the Red LED is not constantly illuminated after an uncharged Battery is inserted into the
Charger, the Battery or Charger may be faulty. Recheck the Battery is fully inserted in the Battery. If
the fault persists do not use and contact your authorised Silverline distributer.
3. When the Battery is fully-charged only the Green LED (18) will be illuminated
Battery Charge Level
The Battery has a built-in Battery Charge Indicator (11). Pressing on the button to the right will
indicate the charge level. The number of bars that illuminate when the button is pressed indicate
the charge level; 1 bar indicating a low charge, 3 bars indicating a full charge.
IMPORTANT: When a low charge level is indicated be aware the tool may stop operating while in
use. This may be dangerous. It is recommended to always ensure the Battery has a good charge
level.
18V Combi Hammer Drill
Notes about battery charging
IMPORTANT: Batteries are an expendable supply whose capacity shortens over time. Always adhere
to the correct handling and charging instructions in the manual. If the battery does not hold charge
or working time is shortened, purchase a genuine Silverline replacement.
• The Battery (12) should be charged at ambient temperatures between 10°C and 40°C (ideally
around 20°C)
• After charging, allow 15 minutes for the battery to cool before use
• Ensure the charger is disconnected from the mains supply after use, and is stored correctly
• Do not leave batteries on charge for extended periods and never store batteries on charge
• The Battery Charger (16) monitors battery temperature and voltage while charging. Remove
the Battery once charging has been completed to maximise charge cycles of the battery and
not waste power
• Batteries can become faulty over time, individual cells in the battery can fail, and the battery
could short. The charger will not charge faulty batteries. Use another battery, if possible, to
check correct functionality of the charger and purchase a replacement battery if a faulty battery
is indicated
• Do not store Lithium-ion battery packs in a discharged state long term. This can damage the
Lithium-ion cells. For long-term storage, store batteries in a high charge state disconnected
from the power tool
• The capacity of batteries will reduce over time. After 100 charge cycles, the battery's operation
time and the performance will slightly reduce. This decline will continue until the battery has
minimal capacity after 500 charge cycles. This is normal and not a fault with the battery pack
Fitting drill bits & accessories
WARNING: Always remove the Battery from the drill before attaching, adjusting or removing
accessories.
WARNING: Do not attempt to tighten drill bits (or any other accessory) by gripping the Chuck
Collar (2) and switching the tool ON. This can lead to personal injury and can cause damage to
the chuck.
WARNING: Never fit any attachment with a maximum speed lower than the no-load speed of
the power tool or selected gear.
1. Open the Chuck Jaws (1) by rotating the Chuck Collar anti-clockwise (with the Chuck facing
the operator)
2. Place the drill bit or accessory centrally into the Chuck Jaws
3. Tighten the Chuck Jaws by rotating the Chuck Collar clockwise
4. When the drill bit or accessory is securely fastened, carefully run the tool to test that it is running
centrally, smoothly and evenly. If the bit is 'wobbling' or not running centrally, release the Chuck
Jaws, check the accessory for damage, correct its position, retighten and test again
Operation
Direction control
WARNING: NEVER change the direction of rotation while the tool is running.
• The direction of rotation can be set using the Forward/Reverse Switch (8)
• For anti-clockwise rotation, holding the drill in a normal operating position, push the switch
to the right
• For clockwise rotation, push the switch to the left
Note: When the Forward/Reverse Switch is in the central position, the drill is locked and cannot
be switched ON. Use this setting as a safety feature to prevent the drill from being switched ON
accidentally.
Speed control
• This drill features a 2-speed gearbox:
- 1st gear range: 0 – 400/min
- 2nd gear range: 0 – 1350/min
• Use the Gear Selector (5) to set the gear: back for first gear, forward for second gear
Note: The first gear would be used normally for driving screws, for example, and offers higher
torque and superior control at low rpm. The second gear would normally be used exclusively for
drilling.
Drill mode selection
• For normal drilling, select the correct gear which is normally the high speed 2nd gear, then rotate
the Mode Selector (4) so the drill symbol is aligned with the indicator on the tool body
• For masonry drilling, select the correct gear which is normally the high speed 2nd gear, then
rotate the Mode Selector so the hammer symbol is aligned with the indicator on the tool body
silverlinetools.com
7