Troubleshooting - STEINEL L 680 LED Instrucciones De Montaje

Manual override function
If a mains switch is installed in the mains supply lead,
the SensorLight provides the following functions in
addition to just being able to switch it ON and OFF:
Sensor operation
1) Switch light ON:
Turn switch OFF and ON once.
Light stays ON for the period selected.
2) Switch light OFF:
Turn switch OFF and ON once.
The light goes out or switches over to sensor mode.
Manual override
1) Activate manual override:
Turn switch OFF and ON twice. The light is set to
stay ON for 4 hours (red LED lights up). Then it
returns automatically to sensor mode (red LED
2) Deactivate manual override:
Turn switch OFF and ON once. The light goes out or
switches over to sensor mode.
Important:
The switch should be actuated in rapid succession
(in the 0.5 – 1 sec. range).
Reset function
The light can be returned to its original settings at any
time (daylight operation 2000 lux, ON time 5 seconds
and basic lighting level OFF).
To do this, hold all three buttons down at the same
time until the LED comes ON and goes out again
(approx. 5 sec.).
Soft light start
The SensorLight features a soft light start function.
This means that when the light is switched ON, it
does not go directly to maximum output but gradually
increases brightness to 50% over the space of one
second. Brightness is also gradually reduced when
the light is switched OFF.
Basic reach setting
The sensor lens is divided into two detection zones.
One half provides a max. reach of 5 m, the other half
a max. reach of 12 m (when installed at a height of
approx. 2 m). After fitting the lens (firmly clip lens into
the groove provided), a small arrow marks the max.
reach of 12 m or 5 m selected (arrow left = 5 metres,
arrow right = 12 metres).
Using a screwdriver, the lens can be unclipped from
the groove at the side and re-positioned for the reach
you require.
Precision adjustment
using shrouds
Shrouds may be used to define the detection zone
exactly as you require in order, for example, to blank
out or specifically target paths or neighbouring prem-
ises. The shrouds can be divided or cut with a pair of
scissors along the vertical and horizontal grooves.
They can be clipped into the top channel around the
centre of the lens. Finally, they are secured in place
after fitting the designer-style trim with glass shade
OFF).
,
(Fig. shows examples of how you can reduce
the angle of coverage and shorten reach.)
Operation / Maintenance
The SensorLight is suitable for switching ON light
automatically. Weather conditions may affect the way
the SensorLight functions. Strong gusts of wind,
snow, rain or hail may cause the light to come ON
when it is not wanted because the sensor is unable to
distinguish sudden changes of temperature from
sources of heat. The detector lens may be cleaned
with a damp cloth if it gets dirty (do not use cleaning
agents).
Caution:
Stainless steel should be cleaned at regular intervals
(about every 3 months) with a standard stainless steel
cleaner. If it is not cleaned, corrosion may occur on the
surface (flash rust).
Declaration of conformity
This product complies with
- Low Voltage Directive 2006/95/EC
- EMC Directive 2004/108/EC
- 10 -

Troubleshooting

Malfunction
SensorLight without power
SensorLight will not switch ON
.
SensorLight will not switch OFF
SensorLight switches ON when it
should not
Change in SensorLight reach
LED ON all the time although
manual override is not selected
LEDs flickering
Functional Warranty
This STEINEL product has been manufactured with
utmost care, tested for proper operation and safety
and then subjected to random sample inspection.
STEINEL guarantees that it is in perfect condition and
proper working order.
The warranty period is 36 months, starting on the date
of sale to the consumer. We will remedy defects caus-
ed by material flaws or manufacturing faults. The
guarantee will be met by repair or replacement of de-
fective parts at our own discretion. The warranty shall
not cover damage to wear parts, damage or defects
caused by improper treatment or maintenance.
Further consequential damage to other objects shall
be excluded.
Cause Remedy
■ Fuse faulty, not switched ON, ■ Fit new fuse; switch ON mains
break in wiring switch; check wiring with volt-
age tester
■ Short circuit ■ Check connections
■ Twilight setting in night-time
■ Reset (button
mode during daytime operation
■ Power switch OFF
■ Switch ON
■ Fuse faulty
■ New fuse, check connection
if necessary
■ Detection zone not properly
■ Re-adjust
targeted
■ Internal electrical fuse has been
■ Switch SensorLight OFF and
activated (LED ON all the time)
back ON again after 5 sec.
■ Continued movement within the ■ Check detection zone and
detection zone re-adjust if necessary
■ Basic lighting level > 0 % ■ Set basic lighting level to 0 %
(button
■ Wind is moving trees and ■ Change detection zone
bushes in the detection zone
■ Cars in the street are being ■ Change detection zone
detected
■ Sunlight shining on the lens ■ Mount sensor in a sheltered
place or change detection zone
■ Sudden temperature changes ■ Change detection zone, change
due to weather (wind, rain, site of installation
snow) or air expelled from fans,
open windows
■ Lens not pressed firmly enough ■ Press lens into groove
into groove
■ Differing ambient temperatures ■ Use shrouds to define detection
zone precisely
■ Internal fuse activated ■ Switch SensorLight OFF and
back ON again after 5 sec.
■ Local power grid ■ see note on page 9
Claims under the warranty will only be accepted if the
unit is sent fully assembled and well packed with a
brief description of the fault, a receipt or invoice (date
of purchase and dealer's stamp) to the appropriate
Service Centre.
Repair Service:
Our Customer Service Department
will repair faults not covered by war-
ranty or after the warranty period.
Please send the product well packed
to your nearest Service Centre.
- 11 -
)
)