Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
TECHNICAL DATA
MODEL
Ø POLISHING FOAM mm
Ø BACKING PAD mm
Ø ORBIT mm
POWER
R.P .M.
WEIGHT
ELECTRONIC SPEED CONTROL
INSULATION CLASS
VOLTAGE
ABSORBED CURRENT
LK900E
7
8
4
INTENDED USE
INTENDED USE
The LK900E heavy-duty polishers is designed for polishing
painted or unfinished metal, fiberglass, and composite surfaces
in professional applications. Common examples of use include but
are not limited to: auto/marine/RV/motorcycle detailing and finish
correction, boat construction and repair, and metal finishing. Do
not use in the presence of flammable liquids or gases.
Do not let children come into contact with the tool. Supervision
is required when inexperienced operators use this tool.
MOTOR
MOTOR
Be sure your power supply agrees with the voltage marked on
Be sure your power supply agrees with the voltage marked on
the nameplate. 120 Volts AC 60Hz means alternating current
the nameplate. 120 Volts AC 60Hz means alternating current
only. Voltage decrease of more than 10% will cause loss of
only. Voltage decrease of more than 10% will cause loss of
power and overheating.
power and overheating.
PARTS OF THE TOOL
PARTS OF THE TOOL
1 - Identification plate
2 - ON/OFF switch
3 - Electronic speed control
4 - Polishing mop (not supplier)
5 - Handle fixing screwa
6 - Switch locking botton
7 - Handle
8 - Velcro faced back up pad
9 - Gasket
10 - Fixing washer
11 - Fixing washer
12 - Screws
ON/OFF SWITCH
ON/OFF SWITCH
WARNING: To reduce the risk of injury, make sure the
WARNING: To reduce the risk of injury, make sure the
polisher is not resting on the workpiece when the
polisher is not resting on the workpiece when the switch
switch is turned on.
is turned on.
To turn the polisher on, push the lever of the switch (2) towards
To turn the polisher on, push the lever of the switch (2) towards
the body of the tool; if the polisher is to be locked in ON position,
the body of the tool; if the polisher is to be locked in ON position,
press button (6) at the same time and keep it pressed while
press button (6) at the same time and keep it pressed while
releasing lever, thus locking the switch.
releasing lever, thus locking the switch.
6
3
ON
OFF
6
5
1
7
2
8
To turn the polisher off, release the lever or, if locked in ON
To turn the polisher off, release the lever or, if locked in ON
position, push the lever to release the lock button.
position, push the lever to release the lock button.
ELECTRONIC SPEED CONTROL
ELECTRONIC SPEED CONTROL
The polisher electronic speed control supply the following
The polisher electronic speed control supply the following fea-
features.
tures.
Speed Adjustment
Speed Adjustment
The speed can be adjusted in two ways: by means of the
variable actuation switch (2), by means of the adjustment wheel
fitted on the upper part of the machine (3).
Adjustment by means of the wheel (3) affects the adjustment
made using the variable actuation switch (2), determining the
maximum speed of the motor.
Speed compensation
The speed must be selected according to the characteristics of
In case of overloading the polisher, the electronic speed control
the pads and those of the material to be machined.
will compensate and maintain the selected speed till a safe level.
Speed compensation
Exceeding this overload level may result in strong vibrations and
In case of overloading the polisher, the electronic speed
tool overtemperature.
control will compensate and maintain the selected speed till
Starting acceleration ramp
a safe level. Exceeding this overload level may result in strong
To avoid kickback effect and compound splattering, the
vibrations and tool overtemperature.
electronic speed control always supply a smooth starting
Starting acceleration ramp
acceleration ramp when the tool is turned on.
To avoid kickback effect and compound splattering, the
Accidental re-start protection
electronic speed control always supply a smooth starting
In case of a sudden lack of main power supply, the electronic
acceleration ramp when the tool is turned on.
speed control prevents the re-start after the power supply
Accidental re-start protection
restoring if the main switch is turned on. The polisher must be
In case of a sudden lack of main power supply, the electronic
turned off and on again pushing the lever of the switch (2)
speed control prevents the re-start after the power supply
toward the body of the tool.
restoring if the main switch is turned on. The polisher must
be turned off and on again pushing the lever of the switch (2)
OPERATION
toward the body of the tool.
WARNING: To reduce the risk of injury, turn unit off and
OPERATION
disconnect it from power source before installing and
WARNING: To reduce the risk of injury, turn unit off and
removing accessories, before adjusting or when making
disconnect it from power source before installing and
repairs. Be sure the switch is in the "OFF" position. An
removing accessories, before adjusting or when
accidental start-up can cause injury
making repairs. Be sure the switch is in the "OFF" position.
WARNING: Never modify any parts of the power tool.
An accidental start-up can cause injury
Damage or personal injury could result.
1
5
9
4
ENGLISH
LK900E
165
125/150
5
900
250÷560
2,70
•
/ II
120 V AC - 60 Hz
7 A
3
ON
OFF
2
6
Publicidad
Tabla de contenido
