Cutting Height Adjustment - Stiga VILLA 320 Instrucciones De Uso

5.4.8 Cutting height adjustment

Indicates lowest cutting height. Used when
raising the deck to washing position and
mounting and dismounting the deck. See
5.4.13.
5.4.8.1 Manual adjustment (320) (4:H)
The cutting height can be set in 9 fixed positions
using the lever.
5.4.8.2 Electrical adjustment (520) (5:O)
The machine is equipped with a control for using
the cutting deck with electrical cutting height
adjustment.
The switch is used to adjust the cutting
height in continuously variable positions.
The cutting deck is connected to the contact (5:S).
5.4.9 Power take-off (5:P)
The power take-off must never be
engaged when the front-mounted
implement is in washing position. This
will destroy the belt transmission.
Switch for engaging/disengaging the electromag-
netic power take-off for operating front-mounted
accessories. Two positions:
1. Press the front part of the switch – the
power take-off is engaged. The symbol
will light up.
2. Press the rear part of the switch – the
power take-off is disengaged.
5.4.10 Clutch release lever (5:R)
A lever for disengaging the variable transmission.
Enables the machine to be moved by hand without
the help of the engine.
The disengagement lever must never be
between the outer and inner positions.
This overheats and damages the
transmission.
Two positions:
1. Lever in– transmission
engaged for normal operation.
2. Lever out– transmission
disengaged. The machine can be
moved by hand.
The machine may not be towed over long distances
or at high speeds. The transmission could be
damaged.
5.4.11 Seat
The seat can be folded and is adjustable
front-rear. The seat is locked in the folded
up position using the catch (6:V).
To adjust the seat, loosen the two screws (6:U), set
the seat to the desired position and tighten the
screws. Tightening torque: 20-24 Nm.
ENGLISH
If the screws are tightened more than 24
Nm, the seat will be damaged.
The seat is equipped with a safety switch
that is connected to the machine's safety system.
This means that certain dangerous activities are not
possible when there is nobody in the seat.
5.4.12 Cover (5:N)
Open the cover to access the fuel lid, fuel
meter and oil tank/dipstick.
The cover is opened by lifting it at the
front edge.
The machine may not be operated un-
less the cover is closed. Risk of burns.
5.4.13 Implement mounts (7:W)
The implement mounts makes it very easy
to shift between the different implements.
The implement mounts allow the deck to
be moved easily between the two posi-
tions:
• Normal position - Locked (with fully tensioned
belt).
• 4 cm behind the normal position - Unlocked
(with slackened belt so that the deck gets closer
to the base machine).
As the belt idler is released from the belt, the im-
plement mounts simplify shifting between imple-
ments and belt replacement.
5.4.13.1Mounting an implement
1. If the implement is a cutting deck: Set the lo-
west cutting height.
2. Place the hooks on the mounting frame around
the mount. See fig 7:X.
3. Place the belt around the pulley on the machine
The cutting deck must never be opera-
ted without the belt protection assemb-
led. Risk of crushing injury.
4. Close and lock the mounts by turning the hand-
les (7:Y) upwards until the hitch (7:Z) locks in
place.
5. Tension the belt by placing the tensioner inside
the belt. See fig.8.
Assemble the belt protection with use of a 17
mm spanner. Make sure the belt protection is in
correct position. See fig 9.
6. If the implement is a cutting deck with electric
height adjustment: connect the cable to the ma-
chine's front right socket (5:S).
7.)Suspend the unit in the implement lifter. See fig.
(4:Z).
Original instructions for use
EN
71