FARFISA INTERCOMS TD2000 Manual Del Usuario página 14

tween 211 e 230, the auxiliary relay operates as an actuator
and, when called, it moves its contacts (C-NC-NO) accord-
ing to the operating mode set in "System"
"relay".
- User address. Storing a user address, that is a block ad-
dress between 00 e 99 and a device address between
001 e 200, the auxiliary relays operates its contacts (C-NC-
NO) only when a "lock release" command arrives from a user
with address equal or higher to that stored in the device; if
address 00-000 is stored, the auxiliary relay will be activated
by the "door release" command sent by any user. Operating
mode of its contacts is set in "System"
"relay".
To program the address select "Relay address" and press
. LCD shows "Enter block address", while on the bottom
of the second line the address currently stored is reported (no
address from factory). With the
if present, and enter the new one, then confi rm by pressing
, display will show "Enter fl at address" whilst, on the bot-
tom of the second line, the currently stored value is reported
(no address from factory). With the
address, if present, and enter the new one, then confi rm by
pressing the key, system returns to the previous menu.
Attention: to identify the users with address equal or
higher to that stored, both block and fl at address must be con-
sidered (for example user 03-123, has an higher address with
respect to the user 02-200).
Storing 00-000, all the users of the system, by pressing the
"open door" button, will activate the auxiliary relay instead of
operating the door release circuit.
Video OFF -1- Start
In this parameter has to be stored the starting (lower) address
of the fi rst group of users which do not have to receive the
video signal (for example users with only audio intercom).
By pressing the key you enter the programming mode.
LCD shows "Enter block address", while on the bottom of
the second line the address currently stored is reported (no
address from factory). With the
if present, and enter the new one, then confi rm by pressing the
key, display will show "Enter fl at address" whilst, on the
bottom of the second line, the currently stored value is report-
ed (no address from factory). With the
fl at address, if present, and enter the new one, then confi rm by
pressing , system returns to the previous menu.
Video OFF -1- End
In this parameter has to be stored the ending (higher) address
of the fi rst group of users which do not have to receive the
video signal (for example users with only audio intercom).
By pressing the key you enter the programming mode.
LCD shows "Enter block address", while on the bottom of
the second line the address currently stored is reported (no
address from factory). With the
if present, and enter the new one, then confi rm by pressing the
key, display will show "Enter fl at address" whilst, on the
bottom of the second line, the currently stored value is report-
ed (no address from factory). With the
fl at address, if present, and enter the new one, then confi rm by
pressing the , system returns to the previous menu.
Video OFF -2- Start
In this parameter has to be stored the starting (lower) address
of the second group of users which do not have to receive the
video signal (for example users with only audio intercom).
By pressing the key you enter the programming mode.
LCD shows "Enter block address", while on the bottom of the
second line the address currently stored is reported (no ad-
dress from factory). With the
present, and enter the new one, then confi rm by pressing
→
"timings"
→
"timings"
key erase the old address,
key erase the old fl at
key erase the old address,
key erase the old
key erase the old address,
key erase the old
key erase the old address, if
display will show "Enter fl at address" whilst, on the bottom of
the second line, the currently stored value is reported (no ad-
→
dress from factory). With the
if present, and enter the new one, then confi rm by pressing
system returns to the previous menu.
Video OFF -2- End
In this parameter has to be stored the ending (higher) address
of the second group of users which do not have to receive the
video signal (for example users with only audio intercom).
By pressing the
→
LCD shows "Enter block address", while on the bottom of the
second line the address currently stored is reported (no ad-
dress from factory). With the
present, and enter the new one, then confi rm by pressing
display will show "Enter fl at address" whilst, on the bottom of
the second line, the currently stored value is reported (no ad-
dress from factory). With the
if present, and enter the new one, then confi rm by pressing
system returns to the previous menu.
Timings
In this section it is possible to program the timings of all the ac-
tuations of the system. By pressing
ming procedure, whilst pressing
ous menu. Parameters that can be programmed are:
- Activation time for S+S-: activation time for the "open door"
circuit (terminals S+ ed S-).
- Activation time for auxiliary relè: activation time for the
auxiliary relay (terminals C, NC ed NO).
With arrows or
and confi rm with the
vious menu.
Activation time for S+S-
By pressing
key backwards you to the previous menu. Entering the menu,
the fi rst line of LCD shows "Enter time", while on the bottom
of the second line the activation time currently stored is report-
ed (1 sec. from factory). With
enter the new one (max. 10sec.) and then confi rm by pressing
, display will show briefl y "saved" after that the system re-
turns to the previous menu.
Attivation time for the auxiliary relay
By pressing
key backwards you to the previous menu. Entering the menu,
the fi rst line of LCD shows "Enter time", while on the bottom
of the second line the activation time currently stored is report-
ed (1 sec. from factory). With
then, enter the new one (max. 98sec.; entering the value 99
the auxiliary relay will act as bi-stable device) and then confi rm
by pressing , display will briefl y show "saved" after which
the system returns to the previous menu.
Administrator Password
From the factory the administrator password is 0039, but it can
be changed with a new one chosen by the installer or the instal-
lation manager. Pressing
and at the end of the second line of the LCD the current admin-
istrator password is reported (0039 from factory), erase the old
one using the
to confi rm, display will briefl y show "saved" after which the
system returns to the previous menu.
Attention: write down and keep the administrator pass-
word in a safety place, without the administrator password it is
impossibile to program the device.
,
key erase the old fl at address,
key you enter the programming mode.
key erase the old address, if
key erase the old fl at address,
you enter the program-
key you return to the previ-
select the parameter to be programmed
key. key backwards you to the pre-
you enter the programming mode, while
erase the old value and then,
you enter the programming mode, while
key erase the old value and
you enter the programming mode
key and then enter the new password, press
,
Mi 2513 - 14 -