Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Miscellaneous
In this section of the menu it is possible to program the general
parameters of the system which are:
-
key to send a call
- Conversation time
- External camera (TLC)
- Welcome message
- LCD contrast
- FW version
With
or
arrows select the parameter to be set and confi rm
with
.
key backwards you to the previous menu.
key to send a call
It is possible to chose the operating mode for sending a call
which can be:
- manual: after dialing the user address, its alias or after se-
lecting the user name from the directory, it is necessary to
press
to send the call;
- automatic: call is automatically sent 3 sec. from when you
have dialed the user address, its alias or you have selected
the user name from the directory, therefore it is not neces-
sary to press
to send a call.
By pressing the
key you enter the programming mode "
key to send a call" and the fi rst line of LCD shows:
-
key to send call? With arrows
<NO> and then press
and returns to the previous menu.
Conversation time
This function extends the conversation time from 90 sec. (fac-
tory value) to 4 min. Pressing
mode "Conversation time 4 min.", while
you to the previous menu. Entering the programming mode, the
fi rst line of LCD shows:
- Conv. time 4 min? With arrows
<NO> and then press
versation time will be extended up to 4 min; it is always pos-
sible to close the conversation at any time by pressing
the door station or hanging-up the handset on the videoint-
ercom. Choosing <NO> the conversation time remains set to
90 sec., but it is always possible to double the conversation
time pressing, on the door station keypad, the
a tone will warn you that the conversation time is going to
expire.
External camera
Enabling this function the door station will manage an external
additional camera besides the one present on the device. When
a video door phone sends the "monitoring" commands, the
door station switches from the two cameras and on the video
door phone you get alternatively the two related images. By
pressing
you enter the programming mode "External cam-
era" and the fi rst line of LCD shows:
- External TLC? With arrows
and then press
to confi rm; the system stores your selec-
tion and returns to the previous menu.
Welcome message
During standard operations, on the LCD of the door station a
welcome message, reporting short info on how to call a user,
is displayed. It is composed of two pages (2 lines for 20 char-
acters each) that can be customized and which would alternate
each 3 seconds. Pressing
"Message programming", whilst
previous menu. The programming section is composed of two
parts:
- Message 1
- Message 2
With arrows
or
wish to modify, then press
display on which it is possible to write a message using the key-
or
select <YES> or
; the system stores your selection
you enter the programming
key backwards
or
select <YES> or
to confi rm. Choosing <YES> con-
or select <YES> or <NO>
you enter the programming mode
key backwards you to the
select which of the two massages you
to confi rm. LCD shows a blanked
pad of the door station as described in the paragraph "How to
use the keypad". After entering the new message, press
store. Proceed in the same way, if required, to enter the second
message.
Attention: it is suffi cient to program only one of the two
messages so that the system considers it as a welcome mes-
sage, in this case the LCD will remain fi x on it.
LCD Contrast
It is possible to adjust the LCD contrast; pressing
the "LCD contrast" menu and the fi rst line of LCD shows:
- LCD contrast: with
the contrast value, as indicated on the display, and press
to confi rm, system stores the entered value and returns to
the previous menu.
Firmware version
Pressing
grammed in the device. Pressing the
the previous menu.
Default
Selecting this command all the system parameters will be restored
to their factory values with the exception of the user directory
which remains programmed at it is.
Attention: administrator password will be restored to its fac-
tory value (0039).
Pressing
LCD shows:
- Default? With arrows
then press
to the factory values and then returns to the previous menu.
on
key when
or
arrows, increase or decrease
LCD will show the fi rmware version currently pro-
you enter the "Default" mode and the fi rst line of
or
select <YES> or <NO> and
to confi rm, system restores all the parameters
to
you enter
the system returns to
Mi 2513
- 15 -
Publicidad
Tabla de contenido
