Warning; Console (Fig. E-1); Buttons; Explanation Of Display Items - Tunturi Cardio Fit T30 Manual Del Usuario

- Insert the safety key into the slot in the console�
- Make sure that the clip of the safety key is properly attached to
your clothing�
Make sure that the clip is not removed from your clothing before
the safety key is removed from the console�
‼ NOTE
• Console will show "- - - -" code when safety key is not in (correct)
position�
Circuit breaker (Fig. E-2 #B)
The equipment is equipped with a circuit breaker that interrupts the
circuit when the electricity load is above the maximum capacity� When
this occurs, the circuit breaker must be pressed�

⚠ WARNING

• Before pressing the circuit breaker, remove the mains plug from
the equipment�
If the equipment shuts down, proceed as follows to restart the
equipment:
- Remove the mains plug from the equipment�
- Press the circuit breaker to restart the equipment�
- Insert the mains plug into the equipment�
‼ NOTE
• Some circuit breakers used in homes are not rated for high inrush
currents that can occur when a treadmill is first turned on or even
during normal use� If your treadmill is tripping the circuit breaker
(even though it is the proper current rating and the treadmill is
the only appliance on the circuit) but the circuit breaker on the
treadmill itself does not trip, you will need to replace the breaker
with a high inrush type� This is not a warranty defect� This is a
condition we as a manufacture have no ability to control�
Unfolding and folding the
equipment (fig. F1-F2)
The equipment can be unfolded for use (fig� F1) and folded for
transport and storage (fig� F2)�
Refer to the illustrations for the correct way of unfolding and folding
the equipment�
Adjust incline setting (Manual)
- Fold up your treadmill� (Up)
- Take out adjuster pad safety pin�
- Adjust the adjuster pad in desired position�
- Secure the adjuster pad position with the safety pin�
- Unfold your treadmill� (Down)
‼ NOTE
• Make sure both adjuster-pads are in same position to avoid your
treadmill to become unstable�

Console (fig. E-1)

⚠ CAUTION
• Keep the console away from direct sunlight�
• Dry the surface of the console when it is covered with drops of
sweat�
• Do not lean on the console�
‼ NOTE
• The console switches to standby mode when the equipment is
not used for 10 minutes�

Buttons

Stop
- Stop workout�
Speed +
- Increases the speed (0�8 ~ 12 KM/H)�
- Pressing once increases the speed 0,1 kph�
- Pressing and holding for two seconds will increase the speed faster�
- Scroll programs and change values in programming mode�
Speed -
- Decreases the speed (0�8 ~ 12 KM/H)�
- Pressing once decreases the speed 0,1 kph�
- Pressing and holding for two seconds will decrease the speed
faster�
- Scroll programs and change values in programming mode�
Mode
- Select program mode
- Confirm setting to enter next step in programming mode�
Prog
- Select program mode� ( P1 ~ P12, FAT)
Start
- Start selected workout
Speed hot keys:
Speed Hot Keys are set as: 2, 3, 4, 5, 6, 7, 8, 9, 10, 11�
For example, the speed changes from any speed to 8 KPH by
pressing the
Speed Hot Key 8�

Explanation of display items

Speed
- Shows the actual treadmill speed in workout mode�
- Shows target speed in programming mode�
Distance
- Shows the ran distance workout mode�
- Shows the target distance when being in programming mode�
- Shows program selection when being in program mode�
Time
- Shows the ran time in workout mode�
- Shows the target time when being in programming mode�
Pulse
- Shows the pulse rate in workout mode, or "P" when no pulse is
measured�
Calories
- Shows the consumed calories in workout mode�
‼ NOTE
• This data is a rough guide for comparison of different exercise
sessions which cannot be used in medical treatment
‼ NOTE
• Display for "Step/ Distance" & "Pulse/ Calories" scans every 5
seconds�
• Use "MODE" button to freeze display, or start scan again when
in freeze mode�
1 7
English