Entry List - NEC HT1100 Manual Del Usuario

Masking Unwanted Area [Blanking]
This feature allows you to mask any unwanted area of the screen im-
age.
Adjust the Top, Bottom, Left or Right blanking with the SELECT
button.
Adjusting Position and Clock [Position / Clock]
This allows you to manually adjust the image horizontally and vertically,
and adjust Clock and Phase.
Horizontal/Vertical Position:
Adjusts the image location horizontally and vertically using the SE-
LECT and buttons.
Clock .............. Use this item to fine tune the computer image or to
remove any vertical banding that might appear. This
function adjusts the clock frequencies that eliminate
the horizontal banding in the image.
Press the SELECT
ing disappears. This adjustment may be necessary
when you connect your computer for the first time.
Phase ............ Use this item to adjust the clock phase or to reduce
video noise, dot interference or cross talk. (This is
evident when part of your image appears to be shim-
mering.) Use the SELECT
the image.
Use "Phase" only after the "Clock" is complete.
Adjusting the position of an image [Image Position]
This option is available only when "Zoom", "V-Zoom" and "Cinema" are
selected in the "Aspect Ratio".
See page E-23 for more details.
Selecting Overscan Percentage [Overscan]
Select overscan percentage (0%, 5% and 10%) for signal.
NOTE: When "Stadium" is selected in "Aspect Ratio", this feature is not available.
NOTE: The "0%" option may not be available depending upon the input signal.
Selecting Signal Type [Signal Type]
Select either the computer signal type or the component signal type.
RGB ............... Computer signal
Component .... Component signals such as Y/Cb/Cr, Y/Pb/Pr
NOTE: This feature is available on the computer signal only. If you do not get a
better picture even when you set "Signal Select" to "Component" in Setup, set
this to "Component".
[Setup Level]
Corrects grayish black so that a black image or dark image looks true
black. To turn on this feature, Select "On".
Selecting Video Filter Level [Video Filter] (not available for Video,
DVI, Component 15kHz and Viewer)
This function reduces video noise.
Off .................. The filter is removed.
Less ............... The low-pass filter is applied partially.
More .............. The low-pass filter is applied fully.
All manuals and user guides at all-guides.com
or
and buttons until the band-
and buttons to adjust
E-32
Image [Page 2]

[Entry List]

Displays the list of the entry signals. Use the SELECT
your remote control or the projector cabinet to select the signal and
press the ENTER button on the remote control or the projector cabinet
to display the Entry Edit Command screen.
Using the Entry List:
Making any adjustments to the current picture will automatically reg-
ister its adjustments to the Entry List. The registered signal can be
loaded any time from the Entry List.
NOTE: Up to 100 presets can be registered except settings on the Picture.
Entry Edit Command:
You can edit signals on the Entry List.
Load ............... Enables you to select a signal from the list.
Store .............. Enables you to store the currently projected signal.
Cut ................. Enables you to remove a selected signal from the list
and place it on the "clipboard" in the projector.
Copy .............. Enables you to copy a selected signal from the list
and place it on the "clipboard" in the projector.
Paste .............. Enables you to paste the signal placed on the "clip-
board" to any other line of the list. To do this, select
"Paste" and then select the line number you want to
paste to. Last press ENTER.
Edit ................ Enables you to change source names.
Source Name:
Enter a signal name. Up to 18 alphanumeric charac-
ters can be used.
Input Terminal:
Change the input terminal. Video and S-Video are
available for composite signal. Component and Com-
puter are available for component signal.
Lock:
Set so that the selected signal cannot be deleted when
"All Delete" is executed.
Skip:
Set so that the selected signal will be skipped during
auto search.
When complete, select OK and press ENTER. To exit
without storing setting, select Cancel. Select "Source
Name" and press ENTER to display the Source Name
Edit window. You can change source name on this
window. Press
which you can enter alphanumeric characters. See
page E-50 for the key function of the software key-
board.
All Delete ....... This feature enables you to delete all the registered
signals in the Entry List.
buttons on
to display the software keyboard,