Assembly; Installing Loop Handle (02); Installing Guard Plate (03, 04); Mounting The Spool Head (05) - AL-KO solo 130 MT Manual De Instrucciones

GB
and thereby result in a deflagration or even
an explosion.
■
Immediately wipe any spilled petrol off the
appliance and the ground. Allow textiles used
to wipe off petrol to dry in a well ventilated
place before disposing of them. Otherwise,
sudden self-ignition may occur.
■
If petrol has been spilled, petrol vapours oc-
cur. For this reason, do not start the engine
at the same location and move it at least 3 m
away.
■
Avoid skin contact with mineral oil products.
Do not inhale petrol vapours. When filling, al-
ways wear protective gloves. Change and
clean protective clothing regularly.
■
Ensure that your clothing does not come into
contact with petrol. If petrol has got onto your
clothing, change it immediately.
■
Never fill the fuel tank while the engine is run-
ning or hot.

4 ASSEMBLY

WARNING! Danger if assembly is not
carried out completely! Use of an incompletely
assembled device can result in serious injury.
■
Only use the device when it is fully assem-
bled!
■
Before switching on, check that all safety and
protective devices are in place and function-
ing correctly!
WARNING! Risk of injury due to detach-
ing appliance parts. Appliance parts detaching
during operation can lead to serious injury.
■
Attach the cutting tools so that they cannot
come loose during operation.
4.1

Installing loop handle (02)

1. Place rubber sleeve (02/1) over shaft (02/2).
2. Place loop handle (02/3) from above and
mating clamp (02/4) from below around the
rubber sleeve.
3. Insert an Allen screw (02/5) from above and
screw on a nut (02/6) from below, then tight-
en slightly. Repeat this step with the other Al-
len screws and nuts.
4. Tighten all Allen screws securely.
4.2

Installing guard plate (03, 04)

1. Insert the 4 Phillips screws M5x16 (03/1)
through the holes in guard plate (03/2).
30
2. Screw the guard plate securely to guard plate
mounting (03/3).
3. Attach guard bar (04/1) with integrated line
cutter (04/2) to guard plate (04/3), then screw
in plastic securing screw (04/4).
4.3

Mounting the spool head (05)

1. Place driver plate (05/1) onto guide pin (05/2)
of the angle-drive gearbox.
2. To lock, insert Allen key (05/3) into the hole
of the driver plate.
3. Screw spool head (05/4) onto the angle-drive
gearbox and tighten.
Note: Left-hand thread! Tighten the spool in
anti-clockwise direction!
4.4

Installing blade or mulching blade (06)

WARNING! Danger of serious injury! A
worn serrated washer (06/5) can allow the blade
or mulching blade to come loose during operation
and cause serious injuries.
■
Be sure to insert the cotter pin (06/8) sup-
plied.
1. Set down the brushcutter so that the cutting
head is pointing upwards.
2. Place driver plate (06/1) onto guide pin (06/2)
of the angle-drive gearbox.
3. Place blade or mulching blade (06/3) onto
driver plate (06/1) so that the hole in the
blade/mulching blade is exactly on the guide
circle of the driver plate.
4. Place flange (06/4) onto the blade or mulch-
ing blade (06/3) so that the flat side is point-
ing towards the blade/mulching blade.
5. Push on the serrated washer (06/5).
6. Screw the fastening nut (06/6) onto the guide
pin (06/2). To do this, insert the Allen key
(06/7) into the holes provided and tighten
with the spark plug spanner.
Note: Left-hand thread!
7. Secure the fastening nut (06/6) with the split
pin (06/8).

5 START-UP

NOTE Inspect the appliance for damage ev-
ery day before starting work, if it is dropped or is
subjected to other impacts. Have any damage re-
paired before putting the appliance into opera-
tion.
Assembly
443443_a