Cleaning & Maintenance - SFA Saniflo SN4 071 Guía De Instalación Rápida

EN-US
Programming
- 1 press on the «NORMAL» button = change to the next level
indicated by a beep. This will increase the amount of inco-
ming water by two seconds.
- 1 press on the «ECO» button = change to the previous level
indicated by a beep. This will decrease the amount of inco-
ming water by two seconds.
When the modification reaches the maximum or minimum
level, the buzzer stops beeping.
Description of the programming levels:
*S = operation of the solenoid valve (filling with clean water)
*P = pump operation (dilution and discharge)
S* S+P*
Basic level 6 s 1 s
level +1 8 s 1 s
level +2 10 s 1 s
level +3 12 s 1 s
level +4 14 s 1 s
• To exit the programming mode automatically: no keys pres-
sed for 5 seconds = the green led turns on.
Note : The water consumption programmed remains in the
memory even after the unit has been disconnected from the
power supply.
6.2 MANAGEMENT OF THE BLACK WATER TANK
ELECTRONIC KEYBOARD
yellow/red
LED
STATUS
OFF green
CAPTEUR
2
OFF yellow
CAPTEUR
1
Sensor 1 : OFF
Sensor 2 : OFF
ON green
CAPTEUR
2
ON yellow
CAPTEUR
1
Sensor 1 : ON
Sensor 2 : OFF
OFF green
CAPTEUR
2 ON
CAPTEUR
flashing red
1
(«FULL»
message
visible)
Sensor 1 : ON
Sensor 2 : ON
Override of the system when 3rd status is reached
Pressing «NORMAL» for 5 seconds will return cycles to nor-
mal operation.
Attention: Prolonged use of the toilet when black
water tank is full can lead to overflow.
7. CLEANING/MAINTENANCE
can be used like any normal toilet and does not re-
SN4 071
quire any particular maintenance.
7.1 CLEANING
• For cleaning, use normal sanitary products.
• Do not use aggressive chemicals (such as acetone, pure
bleach, etc.) that could damage the material of the bowl.
• Use a suitable standard toilet brush; do not use scouring or
abrasive pads.
Normal Cycle
S S+P S
3 s 1 s 3 s
3 s 1 s 3 s
3 s 1 s 3 s
3 s 1 s 3 s
3 s 1 s 3 s
BUZZER
LED
green
LED
Buzzer
USE
OFF Normal
OFF Normal
4 beeps 3 extra cycles
when a allowed.
key is
Control panel
pressed.
then is locked
until the tank
is emptied.
7.2 WINTERIZING
• In the event of a long period without use, rinse the bowl
then drain using the «EMPTY» button.
• Switch off the water and electricity supplies.
• Take the necessary measures to prevent damage caused
by freezing.
• If using antifreeze, use only RV-antifreeze.
8. FAULT FINDING GUIDE
DISCONNECT ELECTRICAL POWER BEFORE
WORKING ON THE UNIT !
S+P
1 s
FAULT
DETECTED
1 s
1 s
The evacuation is
The cycle
clogged.
proceeds
1 s
correctly, the
1 s
motor turns but
water in the
bowl empties
slowly or not
at all.
The cycle The height of
evacuation is too
proceeds
important.
correctly, but
some water
The discharge pipe
remains in the
is pinched.
bowl after a
cycle.
Foreign body into
the bowl.
The motor
rattles or
crunches.
After the Faulty program.
button on the
Faulty control
control panel
panel.
has been
pressed, the
cycle does not
start.
The inlet filter of
the solenoid valve is
The cycle starts
clogged.
but little water
runs in the
The water feed
bowl.
pipe is pinched.
The stop valve is
The cycle
closed.
engages but
water does not
The solenoid valve
run in the bowl
is defective.
10
PROBABLE CAUSES REMEDIES
Dismount and clean the
discharge pipe.
Modify the installation.
Check the route of the
discharge pipe.
• Disconnect the motor
supplies.
• Close water admission.
• Remove the motor unit.
• With a hook, withdraw
all the matters being able
to obstruct the rotation of
macerator.
• With a tool, turn the
turbine in the 2 directions
until rotation is free.
• Re-connect the motor
supplies and press on
the pneumatic contactor
to control the correct
operation of unit.
• Open water supply.
If the macerator remains
blocked, we recommend to
call the SFA-Saniflo after-
sales service.
Replace the control panel
Call the SFA-Saniflo after-
sales service.
Clean the filter of the
solenoid valve.
Check the water admission
pipe.
Open the stop valve.
Change the solenoid valve.